Looks like i have the right camera in my 2022 laramie to add adaptive cruise control? Just add the steering wheel switch and turn on the function? My truck does have collision sensors and emergency braking already
5thGenRams Forums
Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
How to: Add Adaptive Cruise Control, Lane assist, FCW & Auto Hi-beam to Ram 1500
- Thread starter tdb0021
- Start date
Looks like i have the right camera in my 2022 laramie to add adaptive cruise control? Just add the steering wheel switch and turn on the function? My truck does have collision sensors and emergency braking already
No, after you add the switch you must swap out your ABS controller and module, then bleed the brake system and configure it all with AlfaOBD.
Unless you have a Rebel, I think, in which case you'd already have these parts. Then you would just need the switch and configuration changes.
Mopar 68436462AK, Module-Anti-Lock Brake System
Mopar 68415320AA, Abs Control Module
Toperz
Active Member
I believe only TRX may need only switch and programming. Everything else needs ABS, HCU and sometimes DSM modules if not equipped.
Sent from my SM-N986U using Tapatalk
Sent from my SM-N986U using Tapatalk
tdb0021
Well-Known Member
This is correct unless someone has had a different experience
tdb0021
Well-Known Member
This sounds like what happens if you wire the dasm power to a source that is not turned on with remote start. I had the same issue. The dasm needs power with remote start and regular start
vincentw56
Spends too much time on here
- Joined
- Aug 5, 2020
- Messages
- 4,397
- Reaction score
- 2,886
- Points
- 113
- Age
- 54
There is no harness. Did you make your own from the instructions? Just find a power source that is on with a remote start. I think the instructions actually tell you what fuse location has that power.
vincentw56
Spends too much time on here
- Joined
- Aug 5, 2020
- Messages
- 4,397
- Reaction score
- 2,886
- Points
- 113
- Age
- 54
That's the issue. The mirror doesn't power on during remote start. If you can't find the fused power, let me know and I'll look at mine.
Georgf
Well-Known Member
I'll ask here, does anyone know if it can be added Active Park Assist and what is needed for this? I already have 12” screen with Park Assist button, BSM, parking sensors, it seems there is very little left to work Active Park Assist 
Last edited:
vincentw56
Spends too much time on here
- Joined
- Aug 5, 2020
- Messages
- 4,397
- Reaction score
- 2,886
- Points
- 113
- Age
- 54
Yes, it can be added. I did it. All the information is above.I'll ask here, does anyone know if it can be added Active Park Assist and what is needed for this? I already have 12” screen with Park Assist button, BSM, parking sensors, it seems there is very little left to work Active Park Assist
Georgf
Well-Known Member
Found your post with hardware part numbers, but if i just replace the ParkTronic module will it work with my old sensors?
eyerocks
Active Member
- Joined
- Jun 9, 2021
- Messages
- 37
- Reaction score
- 14
- Points
- 8
- Age
- 46
What fuse number did you tap into?
vincentw56
Spends too much time on here
- Joined
- Aug 5, 2020
- Messages
- 4,397
- Reaction score
- 2,886
- Points
- 113
- Age
- 54
No, you have to use what I listed. Plus, you need the two outer sensors for the rear.
vincentw56
Spends too much time on here
- Joined
- Aug 5, 2020
- Messages
- 4,397
- Reaction score
- 2,886
- Points
- 113
- Age
- 54
If you look at the PDF document in the first post, there is a picture of the fuse location.
Ellisstrong
Spends too much time on here
Man y’all added all of this stuff and I’m just trying to figure out how to get mine working again.
ajprestegaard
New Member
- Joined
- Sep 1, 2021
- Messages
- 1
- Reaction score
- 0
- Points
- 1
- Age
- 32
Do you know the mirror jumper harness number needed for the HD?
