5thGenRams Forums

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

What did you do to your Ram today???

Just buy the smoked sequential turn signals off Amazon. And yes you have to take the whole mirror apart to replace but it's not that difficult

You happen to have a link for those turn signal from Amazon?
 
Put my new 6ton jack stands to use.
Safer than what i was using before. These have a safety lock pin.
Checking and retorquing bora spacers.
As expected everything was nice and tight
 

Attachments

  • 20230102_115558.jpg
    20230102_115558.jpg
    237.5 KB · Views: 108
  • 20230102_120842.jpg
    20230102_120842.jpg
    177.8 KB · Views: 109
  • 20230102_121456.jpg
    20230102_121456.jpg
    151.5 KB · Views: 109
Put my new 6ton jack stands to use.
Safer than what i was using before. These have a safety lock pin.
Checking and retorquing bora spacers.
As expected everything was nice and tight
Been looking to buy a new set of jack stands. Where did you buy those?
 
Been looking to buy a new set of jack stands. Where did you buy those?
I bought some off Amazon. Was cheapest place. I bought one of the "used very good" sets to save even more.
BIG RED T46002A Torin Steel Jack Stands: Double Locking, 6 Ton (12,000 lb) Capacity, Red, 1 Pair https://a.co/d/0l8VBga
 
BIG RED T46002A Torin Steel Jack Stands: Double Locking, 6 Ton (12,000 lb) Capacity, Red, 1 Pair https://a.co/d/0l8VBga
Same stands are sold at my local Fleet Farm. I was just looking at them a few days ago.

These are 3 ton. The 6 ton were right next to them.


C973BA64-293D-4A91-A621-A9AB08189D86.jpeg
 
Tried to do the AJT keyfob mod. Unfortunately they AJT case doesn't work with aftermarket keyfob guts even though they look the same. The buttons on circuit board in my Ebay fob are just a hair taller than the factory ones. So when you screw the AJT case down all the way, it causes the tailgate release and remote start buttons to stay depressed. The fob doesn't like this and flashes the red LED.

Put the guts out of one of my factory fobs in it and will be the wife's key. The gray case is fairly close to my ceramic Gray paint.
PXL_20230113_231640557.jpg
 
Same stands are sold at my local Fleet Farm. I was just looking at them a few days ago.

These are 3 ton. The 6 ton were right next to them.


View attachment 148777
I did look into these big red in 6ton, very similar in price and safety pins but couldn't find a store that carried them in my area and I also liked the flat base on the Daytona from harbor freight better
 
Tried to do the AJT keyfob mod. Unfortunately they AJT case doesn't work with aftermarket keyfob guts even though they look the same. The buttons on circuit board in my Ebay fob are just a hair taller than the factory ones. So when you screw the AJT case down all the way, it causes the tailgate release and remote start buttons to stay depressed. The fob doesn't like this and flashes the red LED.

Put the guts out of one of my factory fobs in it and will be the wife's key. The gray case is fairly close to my ceramic Gray paint.
View attachment 148778
color looks spot on,
I am still undecided if I want to go for that green they have for my Tank BTS
 
I did look into these big red in 6ton, very similar in price and safety pins but couldn't find a store that carried them in my area and I also liked the flat base on the Daytona from harbor freight better
I didn't want a flat base because not all concrete is flat. If I was using them in dirt, I'd definitely want the flat base though
 
Finally got my Vice Designs rear tow hook brackets, passenger side was installed but the driver side won't bolt on. One of the holes won't align, no matter what I do and I need to make a run to Lowes to purchase a nut.

Also painted my tow hooks, a ghetto job for now.

Quality looks good tho.
 

Attachments

  • 20230113_152530.jpg
    20230113_152530.jpg
    122.8 KB · Views: 99
  • 20230113_131151.jpg
    20230113_131151.jpg
    96.8 KB · Views: 99
Finally got my Vice Designs rear tow hook brackets, passenger side was installed but the driver side won't bolt on. One of the holes won't align, no matter what I do and I need to make a run to Lowes to purchase a nut.

Also painted my tow hooks, a ghetto job for now.

Quality looks good tho.
That hole looks a little out of round as well. Surprised that passed quality control.

My kit came missing hardware as well. Unfortunately, I never got to use it as it wouldn't work with the Borla tips
 

Users who are viewing this thread

Back
Top