So... tried to install the bedstep tonight after work. Could not break the 2 bolts loose. Used a breaker bar, just an awkward spot to get any leverage. Especially tough with the exhaust still being hot from the drive home. Did anyone else have any trouble removing the 2 existing bolts for the AF? Will try again tomorrow when I have more patience and energy.
5thGenRams Forums
Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
Bed Step Install Doc and Pics
- Thread starter Jstadick
- Start date
No, but I used a 17" long, 1/2" drive, breaker bar
Went back outside and installed it successfully. Bolts came off with ease using the torque wrench. Was avoiding using the torque wrench to break them loose because somebody had told me that it could mess up the calibration of the wrench. Oh well.
Patsy1099
Spends too much time on here
- Joined
- Jan 5, 2019
- Messages
- 2,333
- Reaction score
- 1,294
- Points
- 113
- Location
- People’s Republic of New Jersey
True. I wouldn’t make a habit of that. Surprised the breaker bar didn't do it. Glad you got it done
Taegee2
Active Member
Everyone seems to be back ordered. Found on eBay for $300 with free shipping (Just Search for Mopar 82215289AF and there's only one vendor that has a few left now...it's the new version as I confirmed it with the seller) By the time you pay for shipping at the other sites, it's pretty much the same, a few dollars difference. Just ordered mine.
Last edited:
Did it look like the “F”?
Dr. Jim
Ram Guru
- Joined
- Aug 16, 2018
- Messages
- 763
- Reaction score
- 554
- Points
- 93
- Age
- 76
Yes, from what I can tell. I do not have an AF to compare it to. The AG has the locating pin and bolts up using the two long bolts already on the truck plus the third bolt which comes with the step. Works just like it should.
AMP Research - BEDSTEP | AMP75322-01A | AMP Research
Go ahead and step on it. Bedstep is a real time saver. Not to mention knee and back saver. Strong and rugged, this non-slip, retractable bumper step quickly flips down with the nudge of a foot providing a faster, easier and safer way to load or unload your pickups cargo. Supports up to 300 lbs...
www.amp-research.com
And you might like this also:
AMP Research - BEDSTEP 2 | AMP75414-01A | AMP Research
Side steps for hard-working trucks. The AMP Research Bedstep2 mounts just behind the cab, forward of the rear wheel, providing a faster, easier and safer route to access toolboxes, equipment and cargo in the bed. Easily installed, this frame-mounted, retractable truck step can be mounted on...
www.amp-research.com
Neurobit
RAM Sorcerer
Just got my step today. Total cost was $2.98. 
Jhill
Ram Guru
How does it look retracted?
Neurobit
RAM Sorcerer
Looks the same.
mel_sanchez
Member
- Joined
- May 3, 2019
- Messages
- 9
- Reaction score
- 1
- Points
- 3
- Age
- 28
Thanks for the share! Was looking for a step by step tutorial with photos and happy to found it here.
epmd
Member
- Joined
- May 26, 2019
- Messages
- 18
- Reaction score
- 4
- Points
- 3
- Age
- 52
How did that work out. I think I ordered from the same dealer. Should get mine next week.
KSOTI
Active Member
I installed the amp bed step and I'm happy with it. Paid 260 it arrived in a couple days from auto accessories garage. Installation was easy. be advised you do have to substitute of the M8 bolts for a longer one 44 millimeters Will do it nicely. Easy step up and down plenty of surface area.AMP Research - BEDSTEP | AMP75322-01A | AMP Research
Go ahead and step on it. Bedstep is a real time saver. Not to mention knee and back saver. Strong and rugged, this non-slip, retractable bumper step quickly flips down with the nudge of a foot providing a faster, easier and safer way to load or unload your pickups cargo. Supports up to 300 lbs...
And you might like this also:
AMP Research - BEDSTEP 2 | AMP75414-01A | AMP Research
Side steps for hard-working trucks. The AMP Research Bedstep2 mounts just behind the cab, forward of the rear wheel, providing a faster, easier and safer route to access toolboxes, equipment and cargo in the bed. Easily installed, this frame-mounted, retractable truck step can be mounted on...
sic_infested
New Member
- Joined
- Nov 12, 2019
- Messages
- 3
- Reaction score
- 0
- Points
- 1
- Age
- 39
So apparently the multifunction tailgate is an option that you cant get the factory bed step with. But online dodge has trucks at shows with a step and the multifunction tailgate. I complained to my dealer as I picked the bed utility group that I'm paying full price for this option and losing a part of it. They said theyll install one for me for free. I get the truck on tursday and I guess well see what I find.
It’s a nice must have even if you have to buy it and install yourself. Especially for us older guys. Lol
sic_infested
New Member
- Joined
- Nov 12, 2019
- Messages
- 3
- Reaction score
- 0
- Points
- 1
- Age
- 39
I was willing to buy it but I spoke to the dealer and my sales guy told me that when you pick the multifunction tail gate you dont get it. But when you pick the bed utility group it's supposed to come with it. And because the option didnt say its removed hed mention it to the manager and see if they'd do something for me. Lucky enough they did. Cant wait for this.
