What did you do to your Ram today???

[mesoavery]

I wrapped some interior parts in 3M CFS12 2080 Carbon Fiber. Never wrapped anything before so was pretty apprehensive but taking my time I'm really happy with the results. Normally if I do anything and make even a small mistake I notice and it drives me nuts but I was able to do this and make it look OEM. Would recommend the 3M 2080.

 

[Highertechnology]

I wrapped some interior parts in 3M CFS12 2080 Carbon Fiber. Never wrapped anything before so was pretty apprehensive but taking my time I'm really happy with the results. Normally if I do anything and make even a small mistake I notice and it drives me nuts but I was able to do this and make it look OEM. Would recommend the 3M 2080.

Did you disassemble it all or do the wrap while attached. Looks great!

 

[mesoavery]

Did you disassemble it all or do the wrap while attached. Looks great!

I tested doing it assembled and didn't like it so I disassembled everything except the trim in the doors. Wasn't too difficult though to remove. I couldn't find instruction to remove the upper glovebox so had to figure that out. IMO taking it out made it much easier and allowed me to wrap it all the way around the edges so when reassembled it looks like a single piece of carbon fiber.

 

[CMil527]

I wrapped some interior parts in 3M CFS12 2080 Carbon Fiber. Never wrapped anything before so was pretty apprehensive but taking my time I'm really happy with the results. Normally if I do anything and make even a small mistake I notice and it drives me nuts but I was able to do this and make it look OEM. Would recommend the 3M 2080.

Great job.. come do mine!

 

[Quint]

New 6x9s in all 4 doors, door handle cubbies, and some floorboard leds

Sent from my SM-G988U using Tapatalk

Nice lights. Did you add an amp to to the 6x9s or running off the stock stereo. I'm going to add my 10" sub & amp. Depending on how that goes, I might upgrade all doors to 6x9s and am wondering if the stock system powers it enough or you need a separate amp.

 

[Quint]

Today I replaced the chrome lug nuts with black ones to match the night edition look.

I also added bull rings to the rear. I noticed that it would not sit flush until I cut a wider hole. I didn't use a router but just a small cutting wheel on my Dremel. It worked well and everything looks and works great.

 

[mesoavery]

Great job.. come do mine!

Here is the kit I bought. Was my first time so I'd recommend giving it a try. Worse case you are out $25. Only other thing you need is an exact knife and patience.

https://www.amazon.com/CFS12-CARBON...fe67f&pd_rd_wg=vSxAM&pd_rd_i=B078X3HY7K&psc=1

 

[silverWS6]

I painted my rock rash rings Blue because i didn’t want that silver, only a few bolts until it cures overnight after painting them i used Duracoat Matt clear 3 coats that stuff is tough.

I'm really digging the TRX wheels!

 

[Gandalfgrey]

Looks good . Which mopar wheels are those? Kinda look like the TRX wheels.

Yes they are the guy wanted 20’s & 37’s

 

[BowDown]

I wrapped some interior parts in 3M CFS12 2080 Carbon Fiber. Never wrapped anything before so was pretty apprehensive but taking my time I'm really happy with the results. Normally if I do anything and make even a small mistake I notice and it drives me nuts but I was able to do this and make it look OEM. Would recommend the 3M 2080.

Looks very good, nice

 

[Betohemi661]

finished removing all the emblems and replacing the

 

[Zeeya]

No, not as of yet. I know I received the whole kit within a couple of days. Will see how long it takes to get this part in.
I just ordered the handle kit. One of the companies made a (compartment) that sits down in the handle and provides a storage area there. For 25 bucks I figured what the h---. Will see what it looks like.

These came in today. They fit the rear fold down console cup holders perfectly. You have to use the small adhesive tabs under them so they don't come out when you fold up the lid.

Question::::: I don't hardly ever bring my truck to the carwash, but I could just imagine those guys hitting the door areas and front console and sucking the liners out...




Door Handle Armrest Tray

Amazon: Car Door Side Storage Box for 2021 2020 2019 Dodge RAM 1500 Door Handle Armrest Tray Organizer (Front Door and Rear Door) Set of 4

 

[Zeeya]

New 6x9s in all 4 doors, door handle cubbies, and some floorboard leds

Sent from my SM-G988U using Tapatalk

I just ordered the door handle trays. How do they fit? You beat me to this one.. LOL,,,,

 

[Zeeya]

What did I do to my truck today? I installed the Rebel hood decal.

This was after I helped my neighbor with his new GMC Acadia Denali. He's getting older and asked if I could help him install running boards. So, I installed those for him, then I washed it, clay barred and waxed it for him. He and his wife are celebrating their 56th anniversary this week, so this was an anniversary present for them.

It's been a loooooong day!

Looks great. I have been considering putting the matte black on my black Rebel. Just wondering how it would look?? I don't want to to do a dark matte gray. Just like it being subdued..

 

[Livinfast85]

I wrapped some interior parts in 3M CFS12 2080 Carbon Fiber. Never wrapped anything before so was pretty apprehensive but taking my time I'm really happy with the results. Normally if I do anything and make even a small mistake I notice and it drives me nuts but I was able to do this and make it look OEM. Would recommend the 3M 2080.

wow that came out great!!!

 

[2020Big4x4Horn]

I just ordered the door handle trays. How do they fit? You beat me to this one.. LOL,,,,

They fit well so far.

Sent from my SM-G988U using Tapatalk

 

[HemiDude]

I wrapped some interior parts in 3M CFS12 2080 Carbon Fiber. Never wrapped anything before so was pretty apprehensive but taking my time I'm really happy with the results. Normally if I do anything and make even a small mistake I notice and it drives me nuts but I was able to do this and make it look OEM. Would recommend the 3M 2080.

Looks great!

 

[BowDown]

Optimum no rinse washed it today and ceramic coated my wheel well liners with leftovers









I know, ceramic coating the liners is a bit much but I hate dirty wheel wells on a clean car and dislike washing them as much. Hoping this will make them easier to clean

 

[Jako]

Optimum no rinse washed it today and ceramic coated my wheel well liners with leftovers

View attachment 84923

View attachment 84924

View attachment 84925

View attachment 84926

I know, ceramic coating the liners is a bit much but I hate dirty wheel wells on a clean car and dislike washing them as much. Hoping this will make them easier to clean

I think it's a great idea. Maintaining the liners is a challenge, feel like I'm doing yoga cleaning them.

 

[DanoUF]

Add the AJT shift knob and changed out the chrome lugs to black lugs. I was a little surprised when I removed the OEM shift knob that it is metal. I still like the feel of the AJT better.