What did you do to your Ram today???

[Talpa]

How well does the vinyl stick to the textured plastic?

It’s doing ok. I’m going to redo it and when I do I’ll sand it down lightly

 

[LuvGun]

This is the definition of “point of no return!”

That's for sure. Initially tried a cap wrench and all it did was tweak the bottom of the filter. Band wrench couldn't get enough bite, just slipped. Eventually used 2 stubby phillips screwdrivers, one on each side and it finally budged. Then was able to finish it off with the band wrench.

 

[Patsy1099]

Got my B2Fabrication resonator delete kit today. The quality of this kit is amazing and these 5” tips are monsters! Psyched to install. Will post back sound clip. Here’s a link to the resonator delete thread with a few unboxing pics.

B2Fab resonator delete kit

We have just introduced a resonator delete kit for the 5th Gen Ram trucks. These are mandrel bent 409 stainless and made in the USA. As far as I know these resonator deletes are the only ones on the market that let you reuse your factory exhaust tips, we are also offering our 5" stainless tips...

5thgenrams.com

 

[DesertRebel]

I bought them already painted. Pretty much everyone is using the same seller on eBay who seems to have a pile of every color. He has Delmonico Red it appears.

https://www.ebay.com/itm/2019-DODGE...489709&hash=item260532931b:g:02sAAOSwhyZbtoCx

PART# 6RP44NRVAA 6RP45NRVAA

lol, that's not a "he", that's a dealer in Phoenix... I use them a lot - their website is moparwholeparts.com

They must have the Hulk putting these things on at the factory

I've read that a lot here... I'm dreading removing mine.

 

[DesertRebel]

Removed the carbon filter and installed a K&N 33-2247 drop-in. Not quite ready to pull the trigger on a full CAI.

Any change? Sound? Butt dyno?

Nevermind - I should have kept reading... I saw you already responded to this question.

 

[DesertRebel]

That's for sure. Initially tried a cap wrench and all it did was tweak the bottom of the filter. Band wrench couldn't get enough bite, just slipped. Eventually used 2 stubby phillips screwdrivers, one on each side and it finally budged. Then was able to finish it off with the band wrench.

How does the dealer get them off?

 

[rxit]

Today I installed a Husky 09411 black gearbox, seems well made install was super easy.

 

[RammerGuy]

No, I have not found one yet, but still looking. For alternatives, I installed locking latches to both of my Ram Bins and also purchased a pistol vault that I have cable locked w/i my Ram.

check this out

 

[RickWaz]

check this out

Thanks RammerGuy and welcome to the 5thGenRams Forum! Another poster also sent this link and I ordered the EXxtreme Console Safe(R) the other day. I have yet to install it, but it looks to be a top-notch security vault. And if you use the code "RAMBEAST" you'll save 10% on any order.

 

[AALiVEE]

Thinking about doing that as well. Received a quote for front film protection (bumper, hood and front fenders) and full ceramic for almost $3000. Sound about right?

A little late to the party but...
Sounds a little steep tbh, i did PPF only on bumper but a full ceramic ultra treatment, aprox 1800
But maybe the hood is that expensive to do?

 

[AtlasRam1500]

Had my limited grill wrap today top and bottom of chrome wrap. to body color of truck. center section still chrome Still haven't decided if iit turn out good enough should have went black maybe

 

[Baron74]

A little late to the party but...
Sounds a little steep tbh, i did PPF only on bumper but a full ceramic ultra treatment, aprox 1800
But maybe the hood is that expensive to do?

I'm getting the 3m PPF for the front bumper and the two panels below the headlights as we speak. Cost is $400 plus tax. Got a quote for ceramic coating from a reputable detail shop of $400 if no extensive paint correction is needed. I only have 4300 miles on the truck and didn't note any rough patches when waxing a couple months ago. Hoping I can get both done for around 1k.

 

[Leatherneck1371]

Had my limited grill wrap today top and bottom of chrome wrap. to body color of truck. center section still chrome Still haven't decided if iit turn out good enough should have went black maybe
View attachment 49337

How much did that run?

 

[mbarnes536]

Debadged sides and tailgate and got it ceramic coated

Before





After

 

[tcrutch]

Did a little vinyl wrapping

Looks great. You wrap it yourself? Any tips for where it edges up against the chrome mounding? I did a first attempt and couldn’t get it to look as good as I wanted.


Sent from my iPhone using Tapatalk

 

[rsmeanie]

Toned down the brightness today. Upper and lower grille painted to match. The center section is wrapped in brushed black. Harmon Customs RAM logo with white backlighting. Mirrors wrapped in gloss black.

 

[Livinfast85]

Did a little vinyl wrapping

Looks great! What brand vinyl did you use?

 

[thebluegoat]

Toned down the brightness today. Upper and lower grille painted to match. The center section is wrapped in brushed black. Harmon Customs RAM logo with white backlighting. Mirrors wrapped in gloss black.

View attachment 49372

Ram should offer a sport package on the Limited. That looks awesome.

 

[MrAndrewArnold]

I dropped my truck off at Bodyshop to repair tailgate damage from a forklift.

 

[MrAndrewArnold]

Toned down the brightness today. Upper and lower grille painted to match. The center section is wrapped in brushed black. Harmon Customs RAM logo with white backlighting. Mirrors wrapped in gloss black.

Looks fantastic! Chrome is hideous.