5thGenRams Forums

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

Amateur Radio (ham) install

squid013

Active Member
Joined
Dec 19, 2020
Messages
44
Reaction score
37
It doesnt have the center console, just the tray below the middle seat. Im toying with fashioning my own mount to bolt to the seat studs

Sent from my SM-G973U using Tapatalk
 

mountainmonkey

New Member
Joined
Jan 15, 2021
Messages
3
Reaction score
0
Location
Colorado
I don't believe so. This is the model I bought. Breedlove #930
How did you end up grounding this mount? I just mounted mine and appear to not have a solid ground from the mount to the chassis. Did you have to remove paint from inside the stake pocket before installing the mount? Did you utilize the ground screw on the mount clamp? If so where did you route the ground wire to on the vehicle?
 

rebel70

Active Member
Joined
Feb 6, 2021
Messages
25
Reaction score
40
Hey all! Just joined. Thanks for all the great ideas. Here's a couple shots of my install. I am using the newly released "bulletproof diesel no drill antenna mount" which mounts between the body and third brake light assembly! It works incredibly well and gives you an NMO mount and plenty of cable which I ran through the existing 3rd brake light hole and down the pillar right to my radio brick. Didn't have to mess with any of the upholstery and just fished the cable through from the exterior. The gasket on the mount is solid and has stood up to the elements quite well. I am planning on slapping an all band antenna on to go with my all band radio that's coming in. I am using the Proclip heavy duty mount with a standard mic lip to hold the control head/mic.
 

Attachments

  • antenna mount .jpg
    antenna mount .jpg
    104 KB · Views: 310
  • speaker mount.jpg
    speaker mount.jpg
    156.5 KB · Views: 299
  • control head mount.jpg
    control head mount.jpg
    135.7 KB · Views: 296
  • brick mount.jpg
    brick mount.jpg
    181.7 KB · Views: 316
  • antenna mount 2.jpg
    antenna mount 2.jpg
    65.6 KB · Views: 318

securityguy

Legendary member
Joined
Feb 17, 2019
Messages
5,576
Reaction score
4,217
Location
North Florida
Hey all! Just joined. Thanks for all the great ideas. Here's a couple shots of my install. I am using the newly released "bulletproof diesel no drill antenna mount" which mounts between the body and third brake light assembly! It works incredibly well and gives you an NMO mount and plenty of cable which I ran through the existing 3rd brake light hole and down the pillar right to my radio brick. Didn't have to mess with any of the upholstery and just fished the cable through from the exterior. The gasket on the mount is solid and has stood up to the elements quite well. I am planning on slapping an all band antenna on to go with my all band radio that's coming in. I am using the Proclip heavy duty mount with a standard mic lip to hold the control head/mic.
You have great taste in equipment. Motorola is my old almamatter...my first job as an Engineer out of college. Great stuff!
 

rebel70

Active Member
Joined
Feb 6, 2021
Messages
25
Reaction score
40
You have great taste in equipment. Motorola is my old almamatter...my first job as an Engineer out of college. Great stuff!
Thanks! APX8500 all band going in very shortly ;) love that I can just slap the all band antenna on my single mount and play. Used to have holes all over my last truck... I could not be happier with the mount bulletproof diesel makes. Highly, highly reccomend. Go Moto.
 

funtrucker

Member
Joined
Jul 5, 2020
Messages
16
Reaction score
7
I have a kenwood uhf/vhf under the passenger seat and the head is on an arm bolted to the floor bolt. I use a short magnetic dual band antenna mounted the cab.
 

funtrucker

Member
Joined
Jul 5, 2020
Messages
16
Reaction score
7
need to find a place to run the antenna cable out of the cab without drilling. Any suggestions?
 

brdima

Active Member
Joined
Dec 17, 2018
Messages
86
Reaction score
57
Location
CT
need to find a place to run the antenna cable out of the cab without drilling. Any suggestions?
There is a removable plug under the carpet in the rear cab driver side. I used that and sealed with some flex seal.
 

N3CAL

New Member
Joined
Mar 9, 2020
Messages
4
Reaction score
7
Just finished my install on 2020 1500 Bighorn. The antenna is Diamond CR-320ANMO Tri-Band. The radio is Anytone AT-D578 Tri-Band DMR. Coax and power cable from battery comes in through firewall rubber boot on drivers side. Found the fender mount online at "The Antenna Farm" website. NCG model number DG3ANTNCG for Ram 1500,2500,3500 (2019-2021) Very clean and easy install. SWR on all three bands (2m, 1.2m and 70 cm) are all below 1.3 to 1. The radio has built in Bluetooth and it connects to 1500 radio without any issues both TX and RX through the stereo is nice!
 

Attachments

  • 20210405_172440.jpg
    20210405_172440.jpg
    91.3 KB · Views: 292
  • N3CAL.JPG
    N3CAL.JPG
    116.4 KB · Views: 291
  • 20210408_125107.jpg
    20210408_125107.jpg
    131.3 KB · Views: 276
  • 20210408_125219.jpg
    20210408_125219.jpg
    116.2 KB · Views: 273
  • 20210408_130541.jpg
    20210408_130541.jpg
    104.4 KB · Views: 277
Last edited:

deanathpc

New Member
Joined
Jun 6, 2021
Messages
2
Reaction score
0
Location
Batavia, NY
This thread is very helpful. I'll have to see what I can do to find a way out of the cab for power and antenna. Thanks for everyone who posted locations of grommets etc.
 

Eddie

Member
Joined
Feb 28, 2020
Messages
7
Reaction score
9
I have been putting off this install quite a while. Passed Technician test Jan 2020. Purchased 1500 Eco Diesel May 2020. Installed Compactenna and 3RD Light Bracket. Ran antenna cable down along rear window, it sits in nicely and up thru grommet beside rear floor storage box.

IMG_3858.jpg

Recently purchased a Yaesu FTM-300DR and yesterday went searching for a place to hide it in truck. I decided to hide it in the space reserved for the CD player. Removed the plastic storage cubby there and using a dremel made the open ever so slightly larger.



IMG_3846.jpg

IMG_3847.jpg IMG_3879.jpg
I added a few cable ties and drilled some holes in the plastic underneath to secure it.
IMG_3864.jpg
Drilled a hole on drivers side for mic
IMG_3854.jpg

There was an existing access hole in bulkhead grommet I just had to cut the end of it on the engine side.
IMG_3857.jpg

I used the supplied cable from Yaesu and pushed it thru this grommet. Landed the ground under an existing ground point in engine bay near battery. Installed the hot on a spare lug in main fuse box, this is temporary until i get a chance to install a relay that is operated by ignition on. Right now its always hot.
IMG_3873.jpg

IMG_3875.jpg

Finished product, now I just need to learn how to use it.



IMG_3881 (1).jpg

IMG_3879.jpg
 
Last edited:

brdima

Active Member
Joined
Dec 17, 2018
Messages
86
Reaction score
57
Location
CT
I have been putting off this install quite a while. Passed Technician test Jan 2020. Purchased 1500 Eco Diesel May 2020. Installed Compactenna and 3RD Light Bracket. Ran antenna cable down along rear window, it sits in nicely and up thru grommet beside rear floor storage box.

View attachment 102970

Recently purchased a Yaesu FTM-300DR and yesterday went searching for a place to hide it in truck. I decided to hide it in the space reserved for the CD player. Removed the plastic storage cubby there and using a dremel made the open ever so slightly larger.



View attachment 102963

View attachment 102964 View attachment 102976
I added a few cable ties and drilled some holes in the plastic underneath to secure it.
View attachment 102966
Drilled a hole on drivers side for mic
View attachment 102967

There was an existing access hole in bulkhead grommet I just had to cut the end of it on the engine side.
View attachment 102969

I used the supplied cable from Yaesu and pushed it thru this grommet. Landed the ground under an existing ground point in engine bay near battery. Installed the hot on a spare lug in main fuse box, this is temporary until i get a chance to install a relay that is operated by ignition on. Right now its always hot.
View attachment 102971

View attachment 102972

Finished product, now I just need to learn how to use it.



View attachment 102974

View attachment 102976
Very cool but did you know this radio has a detachable face? So you could separate the radio body from the control face.
 

LocoMorty

New Member
Joined
Aug 31, 2021
Messages
1
Reaction score
1
Location
TX
Here's my install:

Icom 7100 custom marine mount (eBay): https://www.ebay.com/itm/154551317981 rd5.jpg
Dashboard mount from Midwesttrx: https://www.instagram.com/midwesttrx/
rd3.jpg
Ram Mounts Short Double socket arm and base: https://www.rammount.com/part/RAM-B-201U-A
3rd Brake light NMO mount from Bulletproof Diesel https://bulletproofdiesel.com/collections/antenna-mounts
rd1.jpg
Stake bed mount from Breedlove Mounts https://breedlovemounts.com/store/ols/all
rd6.jpg
Rig is mounted under the rear seat and I'm using an LDG 200 antenna tuner into the 102" whip. Why a whip? Because I don't drive very much and just can't justify the cost of a $1.5K plus screwdriver antenna and associated mount for as little as I'll be using the antenna. Regardless, I made a contact into Costa Rica on 17 mtrs while testing it out.

It'll do for my needs.

73
 

Vision

New Member
Joined
Oct 21, 2019
Messages
3
Reaction score
0
I broke my brain figuring this out.
This is my military style 2m antenna. Mounted to the rail with the nuts im showing part number for.
Just got done with it. Will run cable tomorrow.
 

Attachments

  • 0A48E4B8-D032-4ED7-921F-9C7777C9E328.jpeg
    0A48E4B8-D032-4ED7-921F-9C7777C9E328.jpeg
    204.4 KB · Views: 90
  • E8B3E142-B5F2-4978-B96B-D07DCD0CAEB5.jpeg
    E8B3E142-B5F2-4978-B96B-D07DCD0CAEB5.jpeg
    141.2 KB · Views: 94
  • 842520D0-E827-42F5-AA93-E33847788FF9.jpeg
    842520D0-E827-42F5-AA93-E33847788FF9.jpeg
    211.3 KB · Views: 94
  • 8D676D50-CC15-47EC-8C6A-9EDDF53BA38B.jpeg
    8D676D50-CC15-47EC-8C6A-9EDDF53BA38B.jpeg
    176 KB · Views: 81
  • FE6AF114-20C5-42DB-8AF9-649C6A9C9A9A.jpeg
    FE6AF114-20C5-42DB-8AF9-649C6A9C9A9A.jpeg
    117.9 KB · Views: 78
  • 5B997C40-2483-46D5-9E01-63385D741138.jpeg
    5B997C40-2483-46D5-9E01-63385D741138.jpeg
    209.1 KB · Views: 76
  • CDA08922-D2A1-4C29-8FDE-ED1080EAF008.jpeg
    CDA08922-D2A1-4C29-8FDE-ED1080EAF008.jpeg
    159 KB · Views: 73
  • EF1D611C-C613-4CBB-9A10-451E180A02EB.jpeg
    EF1D611C-C613-4CBB-9A10-451E180A02EB.jpeg
    98.9 KB · Views: 71
  • 6A114C88-44E7-43B2-9FD7-7C9F6A07EE3C.jpeg
    6A114C88-44E7-43B2-9FD7-7C9F6A07EE3C.jpeg
    100.8 KB · Views: 72

Vision

New Member
Joined
Oct 21, 2019
Messages
3
Reaction score
0
I broke my brain figuring this out.
This is my military style 2m antenna. Mounted to the rail with the nuts im showing part number for.
Just got done with it. Will run cable tomorrow.
Lil bitty 5ish watt hand held got BIG EARS now. Das all i need for the truck for now.
 

Attachments

  • image.jpg
    image.jpg
    107 KB · Views: 73
  • 64CFD68A-A089-4D3D-AA32-56DCC8D3C984.jpeg
    64CFD68A-A089-4D3D-AA32-56DCC8D3C984.jpeg
    182.6 KB · Views: 71

darokis

New Member
Joined
May 15, 2020
Messages
3
Reaction score
0
Okay, I decided on doing a trunk mount just to test it out. Not 100% sold, seems like it's very low on the truck. I'm either going to need a taller antenna, or move this one back to where I was originally planning.

View attachment 20453

The faceplate of the FTM-400XDR is so light, I just ended up using velcro to put it in position. I can also take it off whenever I want and store it away. It allows for the center console to easily slide fully forward, but it does block the bottom buttons. Leaves plenty of space for me to use the right side of the compartment for my phone when I want to use it for CarPlay and plug it in. For now I'm just letting the hand mic sit in the side store compartment, I think that will be good enough.

View attachment 20454

As for where I put the radio, I ended up making a custom mount under the driver seat to secure it. So much electronic stuff down there with the motors, heaters, amps, that it was hard to fit it in.

I do think I'm going to move the antenna to the rear of the truck. Maybe I will spend the cash on the folding antenna bracket.
When you move the chair does it hit the radio mounted underneath ?
 

edrclark

Moderator
Staff member
Site Supporter & Order Tracking
Site Supporter
Joined
Feb 7, 2018
Messages
1,284
Reaction score
884
Location
Portland, Oregon
Can you take a better picture of the radio mount. I am trying to do the same.
I have ftm-300DR
Actually am in the process of moving the radio to another truck. In process of getting a 2022 ram 2500. Love my ram 1500 but bigger boat needs a bigger truck
 

Users who are viewing this thread

Top