Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
The dealer cannot add the sales code for passive entry as it is not offered as an official accessory like remote start, power side steps, etc.. it has to be done by their regional rep which is unlikely to happen.
I’m just going to do the corner that leaks at the moment. The gap between the window and body is too small to get in there to seal much else without filling the crap out of the whole space.
I updated the seal on the brake light a year ago and that’s been fine since. So as long as I don’t get the...
Add me to the list finally. 9/14/20 build date, 48K miles. Noticed some drips inside a couple weeks ago when washing. Hasn’t rained much lately but finally did today. Water coming in the upper passenger corner. Pulled the roof trim and can confirm a crack both visually and with soapy water and...
Thanks for letting me know, and glad you caught it in time. I’ll get it changed when I can get logged in from a computer.
Sent from my iPhone using Tapatalk
After going what seems like a year or better without the actual stalling issue happening again, this past weekend it happened 2 days in a row, both just under a mile from the house after a cold start. One time was coasting and slowing down to turn left, and the other was same scenario but...
No need for service mode as others have mentioned.
I will say to make sure you do not have the parking brake engaged when you begin. I forgot I had mine set and it took me a little bit to reinitialize the system as it couldn’t seem to figure out what position they were in and would not...
Posted this in another thread asking about wiring some aux lights, but I'll post it again here since its specific to the bed lights.
I used a 3-position Single Pole Double Throw (SPDT) switch to operate my bed light strips I installed under each rail.
Center terminal goes to the lights. The...
I used a Single Pole Double Throw (SPDT) switch to produce a similar set up on my bed lights.
Center terminal goes to the lights, one side comes from a constant 12V source, the other side comes from the overhead lights. I can select "on" at any time using the constant feed, "switched" which...
If you’re gonna go body color let me know…I’m almost positive I have the original handles still from when I had my bighorn that will work on your rear doors (bright white). Otherwise you can get all 4 that work with PE and run the wires to the rear doors as well.
Sent from my iPhone using...
I’m on QR 39.62 with my 8.4 Nav unit and the Uconnect site says my truck is up to date.
A previous update had the off-road pages show up as part of the update, then a day later the radio rebooted while driving and they went away.
Now I cannot get the off-road pages to come back even using...
To my knowledge, unless they have released them recently, the textured black handles are not available in the PE version.
You would have to choose a different color, or buy whatever color and then just remove the cover from the handles and swap them with yours. You’d need to trim a small hole...
Pretty much 0% chance of a dealer doing it. They don’t even have the ability to make the needed changes in the bcm to make it actually work. They won’t do stuff that isn’t tied to your vin, or available as an official Mopar accessory.
It actually took me longer to bleed the brakes and make the...
If you already have the FCW+, you should just need to swap the ABS module, HCU, and add the switch. Plus the changes using AlfaOBD.
Only downside I see with adding this if it didn’t come from the factory, assuming the install was done properly, would be warranty coverage related to brakes if...
Got the parts installed tonight and ACC functions as intended. After a few frustrating moments thinking the truck was going to be stuck sideways in the garage overnight, I was able to get things figured out and cleared all codes and lights. The parking brake would not release at first, I'm...
Forgot to tag you in my post, realized after the fact you probably had the answer from your testing as well. That’s what I was thinking about the vin. It was a new unit and only installed on my truck that day I tested it. Thanks for confirming.
Sent from my iPhone using Tapatalk
Finally ordered the HCU and hoping to tackle the ACC in the next day or two.
@Jimmy07, can you think of any reason the ABS module I ordered way back to test out wouldn’t work with the new HCU since I did have it installed in the truck for a day or so with the incompatible HCU? I wouldn’t think...
It doesn’t bother me. Even with the heavier tires I still get much better mileage than my Titan did. Plus the trade off for better stability and traction is worth it to me.
Sent from my iPhone using Tapatalk
You can catch the wires right by the b-Pillar in the floor channel since they run from the RF hub on the back wall up to the front doors that way.
Sent from my iPhone using Tapatalk
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.