Nicely done. What vehicle did you choose to program the keys fob with jscan?I just used JScan to retrieve my 5 digit PIN. The instruction tell you to turn the ignition off but after several failed attempts while screwing around I tried it with the ignition on and hazards on and it spit out my 5 digit PIN. I then used the PIN to program my new key fob (Made out of chinesium) and it it worked flawlessly. I am ending on a high note for tonight but as a weekend project I will try to enable remote start.
Well, I guess that would be relevant information. I have a 2023 Ram 2500 with the Cummings diesel.Nicely done. What vehicle did you choose to program the keys fob with jscan?
The HDs, still being 4th gen, are known to work for programming key fobsWell, I guess that would be relevant information. I have a 2023 Ram 2500 with the Cummings diesel.
That’s why I asked. Was hoping he had a 5th genThe HDs, still being 4th gen, are known to work for programming key fobs
Well, I guess that would be relevant information. I have a 2023 Ram 2500 with the Cummings diesel.
You are the man @Jimmy07 ! Thank you !!!Alright…
Finally grabbed a handful of fobs from eBay and successfully programmed to 2019+ 5th GEN Ram 1500 using only JScan.
All steps were done without ever putting the ignition in ACC or RUN position, and all working fobs were left in the house (so I could verify that JScan can program for an “all fobs lost” situation).
Connect to Ram DT 1500, then go to adaptation > radio frequency hub settings > RFH pin reading beta > target value = ram 2019-2023 > go.
When the following screen pops up, just turn the hazards on. Don’t bother opening and closing the door and don’t worry about the instrument cluster:
View attachment 185176
Once the pin is read, a screen pops up that says put ignition in run- don’t touch the ignition switch, just press OK, and it will say successful, and you’ll be left with this screen:
View attachment 185177
Press back to go back to the list of radio frequency hub settings, and choose RFH ignition key programming (pase) beta.
Keep clicking GO until you get to the screen to enter the PIN, and enter it.
Keep pressing GO for the next few screens, note that the unlock button press is mentioned, but will not be performed:
View attachment 185178
View attachment 185179
This next screen is where the programming happens, so once you get to this one, just start pressing the ignition button with the fob:
View attachment 185180
And after a few seconds of that:
View attachment 185181
These are the fobs I use:
FOR 2019 20 21 23 24 RAM 1500 SMART KEYLESS PROXIMITY REMOTE KEY FOB OHT-4882056 | eBay
2019 - 2024 Dodge Ram 1500 Pickup. Dealer/Locksmith to program and cut the remote key. Buttons: Lock, Unlock, Panic, Remote Start, Power Tailgate. Test Key: Y159.www.ebay.com
Alright…
Finally grabbed a handful of fobs from eBay and successfully programmed to 2019+ 5th GEN Ram 1500 using only JScan.
All steps were done without ever putting the ignition in ACC or RUN position, and all working fobs were left in the house (so I could verify that JScan can program for an “all fobs lost” situation).
Connect to Ram DT 1500, then go to adaptation > radio frequency hub settings > RFH pin reading beta > target value = ram 2019-2023 > go.
When the following screen pops up, just turn the hazards on. Don’t bother opening and closing the door and don’t worry about the instrument cluster:
View attachment 185176
Once the pin is read, a screen pops up that says put ignition in run- don’t touch the ignition switch, just press OK, and it will say successful, and you’ll be left with this screen:
View attachment 185177
Press back to go back to the list of radio frequency hub settings, and choose RFH ignition key programming (pase) beta.
Keep clicking GO until you get to the screen to enter the PIN, and enter it.
Keep pressing GO for the next few screens, note that the unlock button press is mentioned, but will not be performed:
View attachment 185178
View attachment 185179
This next screen is where the programming happens, so once you get to this one, just start pressing the ignition button with the fob:
View attachment 185180
And after a few seconds of that:
View attachment 185181
These are the fobs I use:
I tried the way the app tells you and the way @Jimmy07 says to do it. no luck either way...two fobs, same luck....i am using the android phone app....maybe that's the issue? also using OBDLink® MX+ and SGW.Alright…
Finally grabbed a handful of fobs from eBay and successfully programmed to 2019+ 5th GEN Ram 1500 using only JScan.
All steps were done without ever putting the ignition in ACC or RUN position, and all working fobs were left in the house (so I could verify that JScan can program for an “all fobs lost” situation).
Connect to Ram DT 1500, then go to adaptation > radio frequency hub settings > RFH pin reading beta > target value = ram 2019-2023 > go.
When the following screen pops up, just turn the hazards on. Don’t bother opening and closing the door and don’t worry about the instrument cluster:
View attachment 185176
Once the pin is read, a screen pops up that says put ignition in run- don’t touch the ignition switch, just press OK, and it will say successful, and you’ll be left with this screen:
View attachment 185177
Press back to go back to the list of radio frequency hub settings, and choose RFH ignition key programming (pase) beta.
Keep clicking GO until you get to the screen to enter the PIN, and enter it.
Keep pressing GO for the next few screens, note that the unlock button press is mentioned, but will not be performed:
View attachment 185178
View attachment 185179
This next screen is where the programming happens, so once you get to this one, just start pressing the ignition button with the fob:
View attachment 185180
And after a few seconds of that:
View attachment 185181
These are the fobs I use:
FOR 2019 20 21 23 24 RAM 1500 SMART KEYLESS PROXIMITY REMOTE KEY FOB OHT-4882056 | eBay
2019 - 2024 Dodge Ram 1500 Pickup. Dealer/Locksmith to program and cut the remote key. Buttons: Lock, Unlock, Panic, Remote Start, Power Tailgate. Test Key: Y159.www.ebay.com
New to the forum hello everyone this seems to be the only thread of information on this topic then I can find anywhere. I spent over 2 hours trying to program a key last night on a 22 RAM limited with no success. I used the guide that @Jimmy07 posted on June 22nd. I'm using a Galaxy Note 20 ultra an autel bypass cable & OBD link MX+. With the newest versions of both JScan and alfaOBD. Although the pin pulled within seconds on the first try programming repeatedly failed no matter how I held the key. The “FOBIK is Not Blank" error message continually popped up. I tried his way and every other variation I could think of. @jq5thgen mentioned on page 7 of this thread finding a service bulletin saying that didn't necessarily mean the key had been used. I found the same & also mentioned finding success pulling the pin with JScan and then using alfaOBD to program the key. This was not successful for me either The key was purchased new from Amazon I have sent it in for return and purchased a six-button fob from the recommended eBay store. I'll update if I'm successful if anybody has any advice I'm all ears thanks.
New to the forum hello everyone this seems to be the only thread of information on this topic then I can find anywhere. I spent over 2 hours trying to program a key last night on a 22 RAM limited with no success. I used the guide that @Jimmy07 posted on June 22nd. I'm using a Galaxy Note 20 ultra an autel bypass cable & OBD link MX+. With the newest versions of both JScan and alfaOBD. Although the pin pulled within seconds on the first try programming repeatedly failed no matter how I held the key. The “FOBIK is Not Blank" error message continually popped up. I tried his way and every other variation I could think of. @jq5thgen mentioned on page 7 of this thread finding a service bulletin saying that didn't necessarily mean the key had been used. I found the same & also mentioned finding success pulling the pin with JScan and then using alfaOBD to program the key. This was not successful for me either The key was purchased new from Amazon I have sent it in for return and purchased a six-button fob from the recommended eBay store. I'll update if I'm successful if anybody has any advice I'm all ears thanks.
This is great advice I can't believe I have not read this anywhere else I did not know this. After researching a little bit I don't think it applies to my particular situation. The fob I purchased had The buttons aligned vertically whereas the heavy duty Rams seem to have them aligned horizontally from my understanding. Maybe a four button fob can't be programmed to The limited trim level.....? https://www.amazon.com/gp/aw/d/B0CRQVKBB7?psc=1&ref=ppx_pop_mob_b_asin_titleVerify the key that you were sent was for a 1500 and not a 2500. I had the same issue using an Autel KM100 key programmer. Turned out amazon had sent me keys for a 2500 which are different.
Went to ebay and bought 2 new 4 button fobs that listed the actual chip specs that matched my factory key and those programmed with out a single issue.
This is great advice I can't believe I have not read this anywhere else I did not know this. After researching a little bit I don't think it applies to my particular situation. The fob I purchased had The buttons aligned vertically whereas the heavy duty Rams seem to have them aligned horizontally from my understanding. Maybe a four button fob can't be programmed to The limited trim level.....? https://www.amazon.com/gp/aw/d/B0CRQVKBB7?psc=1&ref=ppx_pop_mob_b_asin_title
I appreciate the advice thank you for your contribution as I had previously stated I have since returned and purchased from an eBay seller several other members have recommended in this thread.This should be the equivalent key for 1500 for the same seller I used for my 2500. Stop buying random Amazon crap. These are half the price anyway.
5-BTN Smart Remote Key Fob 68442909 OHT-4882056 for 2019 2020 2021 2022 Ram 1500 | eBay
Find many great new & used options and get the best deals for 5-BTN Smart Remote Key Fob 68442909 OHT-4882056 for 2019 2020 2021 2022 Ram 1500 at the best online prices at eBay! Free shipping for many products!www.ebay.com
When I bought my 2022 Night Edition earlier this year it only came with one fob. The dealer said they would cover the cost of a new key, but its been pretty hard to find someone here in Sweden that could do the programming where I did not have to drive all they way to Stockholm (600miles round trip from where I live) to get it done. The dealer supplied me with a new original fob from Mopar, 6839 9889 AA, its the correct part number for the 1500 and it was in a sealed bag so its never been used.
Decided to try and program it my self with JScan. Allready had the by pass cable and the OBDLink MX+ since I needed to change the tire size to 35" .. The PIN kode was read in less than 30 secs. Then I tried the programming multiple times, but it would fail with the error about fob not being blank. And then it hit me, maybe for some reason it was detecting my working fob that I had in my pocket. Took the fob out and left in the house, and the programming worked on the first try.
Dont know if I was just lucky, or the not blank fob error has something todo with a working fob being in proximity during the programming. Thought I would just metion this, it might help somebody else with this error. And @Jimmy07 did mention that he did the programming without a working key present.
Anyways I'm happy, got two working fobs now