What did you do to your Ram today???

[Nozzleman]

What set did you go with?


Sent from my iPhone using Tapatalk

https://www.amazon.com/dp/B08M36JV71/ref=cm_sw_r_cp_apa_fabc_SMHE8QVKYZ7P01MCR5GC?_encoding=UTF8&psc=1

Sent from my SM-N970U using Tapatalk

 

[Lufty]

Picked up the Rebel from being ceramic coated...

 

[kevinvw]

I’ll post more when I get it back from the shop on Saturday.

I’ll take a couple of other angles tomorrow but I’m really really pleased with how this came out. The lines on the roof are on point and I love the look from inside the cabin. Still get a ton of light in there.

 

[Scooter29]

https://www.amazon.com/dp/B08M36JV71/ref=cm_sw_r_cp_apa_fabc_SMHE8QVKYZ7P01MCR5GC?_encoding=UTF8&psc=1

Sent from my SM-N970U using Tapatalk

Been looking at these but wasn’t sure in the details of plug and play like they say. Did you have to get a harness for them to work? And does it use a fuse tap to power the running lights? Thanks

 

[Nozzleman]

Been looking at these but wasn’t sure in the details of plug and play like they say. Did you have to get a harness for them to work? And does it use a fuse tap to power the running lights? Thanks

So it is a direct plug in, no harness needed. The fit is dead on.
The harness that comes with it to add the daytime running lights, doesn't fit, BUT, I didn't want that feature anyways, although, if you do want to add it, you just have to order a $5 adapter for it on Amazon, no biggie.

Let me know if you have any other questions. More than happy to answer.

Sent from my SM-N970U using Tapatalk

 

[Neurobit]

Replaced my older prior-gen Valentine V1 with a Uniden R7, and also replaced my broken Car2Play dongle with a AirlinKit brand, so a fun day all around for the Silver Bullet.

 

[Scooter29]

So it is a direct plug in, no harness needed. The fit is dead on.
The harness that comes with it to add the daytime running lights, doesn't fit, BUT, I didn't want that feature anyways, although, if you do want to add it, you just have to order a $5 adapter for it on Amazon, no biggie.

Let me know if you have any other questions. More than happy to answer.

Sent from my SM-N970U using Tapatalk

Do you know possibly know what the adapter needed is so I could order all together? And I’m guessing the light output is definitely better than the stock halogens ha.

 

[Nozzleman]

Do you know possibly know what the adapter needed is so I could order all together? And I’m guessing the light output is definitely better than the stock halogens ha.

Yup, light output is definitely better.

This is the wire, so you just have to cut the wire they send you and the end where in plugs into your fuse box and replace it with this one, should work fine. Hope it helps.

https://www.amazon.com/dp/B06XKD7SV6/ref=cm_sw_r_cp_apa_fabc_K9X6JPZWCFN4B82ANGZ9

Sent from my SM-N970U using Tapatalk

 

[Scooter29]

Yup, light output is definitely better.

This is the wire, so you just have to cut the wire they send you and the end where in plugs into your fuse box and replace it with this one, should work fine. Hope it helps.

https://www.amazon.com/dp/B06XKD7SV6/ref=cm_sw_r_cp_apa_fabc_K9X6JPZWCFN4B82ANGZ9

Sent from my SM-N970U using Tapatalk

Right on, thanks for the info I appreciate it a lot.

 

[Gandalfgrey]

Today i installed my Tazer DT and adjusted for tire size & tire pressures , also ordered my winch Zeon platinum 10 , this winch will just be easier to run having a remote clutch, using a SwarfWorks mount .

 

[Scram1500]

Put on new headlights. Love em!

Sent from my SM-N970U using Tapatalk

Look sharp! Let us know how they work out after a while

 

[SpeedyV]

Removed, cleaned, re-greased, and reinstalled my Hellwig sway bar. It was getting a little “creaky” when lowering the truck. Went with the middle setting this time, and I’m liking it so far!

 

[Ellisstrong]

Removed, cleaned, re-greased, and reinstalled my Hellwig sway bar. It was getting a little “creaky” when lowering the truck. Went with the middle setting this time, and I’m liking it so far!

Dang I wonder if that is what I hear sometimes when I lower mine. Now I have to go check

 

[HemiDude]

Installed my Pulsar. Drove down to the gas station and filled it with 93, then drove around for half an hour. Pretty pleased with the upgrade

 

[FiremanHemi]

Installed the Motofab 2.5 Level
Atturo Trailblade XT 35x12.50R20
2” Wheel Spacers

 

[Todd_S]

I ordered these utility rails. I want to get the riv nuts installed before I have it coated with Line X.

Utility Rails for Conventional Bed - Dodge RAM | Auto Parts

Pickup Box Utility Rails For 5-Ft 7-Inch Conventional Bed for 2019-2020 RAM 1500 DT 5th Gen

www.bamwholesaleparts.com

 

[tones2SS]

Installed the Motofab 2.5 Level
Atturo Trailblade XT 35x12.50R20
2” Wheel Spacers
View attachment 85668

That looks great!
How the ride?

 

[z0n3]

Pulled the Hellwig off today and reapplied some grease to the bar, and bushings. It developed a squeak when I transferred it from my 2019. Hellwig was nice enough to send me a few packets of their grease for free too!

 

[dearchristopher]

I ordered these utility rails. I want to get the riv nuts installed before I have it coated with Line X.

Utility Rails for Conventional Bed - Dodge RAM | Auto Parts

Pickup Box Utility Rails For 5-Ft 7-Inch Conventional Bed for 2019-2020 RAM 1500 DT 5th Gen

www.bamwholesaleparts.com

my truck came factory with these. super handy for adjustable tie downs. i have some plans in the works to build a folding awning mount so i can get an awning on the truck.

quick ipad sketch on what i’m thinking. i have some notes somewhere on some fasteners from amazon that will work with the rail, so i can build some other stuff once i get the awning together.


Sent from my iPad using Tapatalk

 

[securityguy]

my truck came factory with these. super handy for adjustable tie downs. i have some plans in the works to build a folding awning mount so i can get an awning on the truck. quick ipad sketch on what i’m thinking. i have some notes somewhere on some fasteners from amazon that will work with the rail, so i can build some other stuff once i get the awning together.

Your truck came with the Bed Utility Group which is why you have the rails.