5thGenRams Forums

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

What did you do to your Ram today???

securityguy

Legendary member
Joined
Feb 17, 2019
Messages
5,581
Reaction score
4,224
Location
North Florida
My comment about Motorola was in regards to components used and build quality. General Electric was old tech, EF Johnson two-way was visionary IMO and the Sonar Radio from Fla was the bomb.
I worked out of their Regional HQ near the BWI airport in the mid-late 80's...grew up north of Baltimore and went to University of Maryland. We never saw GE as a real competitor...EFJ was a good product.
 

NewTruckWhoDis

Active Member
Joined
Feb 14, 2020
Messages
198
Reaction score
140
Location
Northern VA
Not only that they also changed the light under the dash (the one which shines on pedals). No more pop the plastic cap and put your LED. Now it is LED soldered on the pcb deal.. so no cool colors for me :-(
Learned that one the hard way. Planned to give the Lasfit bulbs to a buddy with a bighorn. I assumed it was a trim thing and not based on year. Guess I will have him check his footwell lights first.
 

Trailrunner77

Member
Joined
Sep 11, 2020
Messages
8
Reaction score
17
0aca806e91cc269993302f24d632bcd3.jpg

939635a658d6bfd8373e1f828be13448.jpg

Installed the Rough Country 6” grille light kit today, took a bit of time to install but was worth the effort. They are a flood light so they light up the ditches better and should make it easier to spot critters that roam at night.


Sent from my iPhone using Tapatalk
 

vincentw56

Spends too much time on here
Joined
Aug 5, 2020
Messages
3,139
Reaction score
2,236
Not only that they also changed the light under the dash (the one which shines on pedals). No more pop the plastic cap and put your LED. Now it is LED soldered on the pcb deal.. so no cool colors for me :-(
I found that out the hard way too.

Sent from my SM-G988U using Tapatalk
 

NewTruckWhoDis

Active Member
Joined
Feb 14, 2020
Messages
198
Reaction score
140
Location
Northern VA
939635a658d6bfd8373e1f828be13448.jpg

Installed the Rough Country 6” grille light kit today, took a bit of time to install but was worth the effort. They are a flood light so they light up the ditches better and should make it easier to spot critters that roam at night.


Sent from my iPhone using Tapatalk
Appreciate your picture. Those certainly appear much brighter than I would have guessed. I've been planning on getting them, but wasn't sure they would be bright enough to be anything more than running lights, or DRLs.

How'd you wire them? Dedicated switch, or with running lights/high beams, etc.?
 

D.Sull

Active Member
Joined
Mar 9, 2020
Messages
50
Reaction score
97
Location
McCalla, AL

securityguy

Legendary member
Joined
Feb 17, 2019
Messages
5,581
Reaction score
4,224
Location
North Florida
Thanks...where did you go to bring the wires up into the cab for connection?
 

D.Sull

Active Member
Joined
Mar 9, 2020
Messages
50
Reaction score
97
Location
McCalla, AL
Thanks...where did you go to bring the wires up into the cab for connection?
Ran the wires into the engine bay and through the firewall. On my limited, there's a small nipple below the main wire bundle coming through the firewall. I snipped the end off of it, ran a piece of wire through, and tapped into the foot well lights. Backfilled with some RTV sealant where I cut.
 

securityguy

Legendary member
Joined
Feb 17, 2019
Messages
5,581
Reaction score
4,224
Location
North Florida
Ran the wires into the engine bay and through the firewall. On my limited, there's a small nipple below the main wire bundle coming through the firewall. I snipped the end off of it, ran a piece of wire through, and tapped into the foot well lights. Backfilled with some RTV sealant where I cut.
Thanks...haven't looked to see if there was a grommet in the vehicle floor we could come up through. I'll check it out closer and look at the grommet you mentioned. Where did you pick up the hot wire for when the door is open?
 

Bootleg

Active Member
Joined
Jan 3, 2020
Messages
33
Reaction score
39
Not only that they also changed the light under the dash (the one which shines on pedals). No more pop the plastic cap and put your LED. Now it is LED soldered on the pcb deal.. so no cool colors for me :-(
I found this in another thread. I bought the Lasfit LED lights for my Limited, they won't work since Limiteds and many others are fully LED already on the inside. I really want to do this kit on mine.
 

obrien

Active Member
Joined
Dec 3, 2020
Messages
155
Reaction score
116
I found this in another thread. I bought the Lasfit LED lights for my Limited, they won't work since Limiteds and many others are fully LED already on the inside. I really want to do this kit on mine.
but that that is only for 2020 and it is $200.. So far I have changed to LED in map light, dome and vanity and the difference is stunning. sorry for the low quality pic I just snap it really quick but I am sure you can tell how bright and modern looking it is. And for like 50 usd
 

Attachments

  • 20210115_205544.jpg
    20210115_205544.jpg
    61.6 KB · Views: 145

Bootleg

Active Member
Joined
Jan 3, 2020
Messages
33
Reaction score
39
but that that is only for 2020 and it is $200.. So far I have changed to LED in map light, dome and vanity and the difference is stunning. sorry for the low quality pic I just snap it really quick but I am sure you can tell how bright and modern looking it is. And for like 50 usd
Actually, it's for 2019-2021, according to their site. Apologies, I was on the specific page. Here's the main page for 5th gen Rams
 

Night Rebel

Well-Known Member
Joined
Jun 17, 2020
Messages
214
Reaction score
204
Location
Atlanta, Ga
My lights were just delivered by Amazon...too dark out now to put them on. Will try tomorrow when I get a bit of free time. Night...what did you use to pry out the existing light so you don't "damage" or mark up the mirror itself by just shoving a screwdriver in there? Any tips are appreciated my friend!
I just used a small pocket flat head screwdriver. There is a couple videos on YouTube where they show ya where to pry. I wasn’t to worried about scratching the plastic so much but me dropping the screwdriver and hitting the door or something. It’s pretty hidden so prob won’t see the bottom of the mirror anyway.
 

abtennyson

Active Member
Joined
Dec 30, 2020
Messages
26
Reaction score
17
Over the weekend installed this switch panel for my hidden light bar and rear cube lights. Also installed a train for from Amazon for $35, can’t speak on the longevity of it yet but so far it sounds good, doesn’t seem to cheaply made, and if it doesn’t work out I’m sure it won’t be the last $35 wasted. Mounted the horn button on the window sill, wasn’t sure if I wanted it into the switch panel as I am unable to program them to be momentary switches/buttons.

Next up tonight’s project: LED interior lights
 

Attachments

  • C6B1F9CF-E26C-4DAC-8D49-A8B6B9DBC689.jpeg
    C6B1F9CF-E26C-4DAC-8D49-A8B6B9DBC689.jpeg
    140.6 KB · Views: 252
  • DA37339A-FE83-4BB9-9452-95094443D682.jpeg
    DA37339A-FE83-4BB9-9452-95094443D682.jpeg
    137.5 KB · Views: 252
  • 19C6BE56-5D4B-49D2-BCDF-E3F6B5BB1256.jpeg
    19C6BE56-5D4B-49D2-BCDF-E3F6B5BB1256.jpeg
    125 KB · Views: 252

Users who are viewing this thread

Top