Wiring harness

[Tricknine]

I am needing some help on how to wire the 6 pin male subwoofer plug. The how to wire it in to the ANC module. I have read somewhere on here just not positive how to go about it.?

 

[Diamondback]

If there are pins located in the connector already, then you remove those (use small pin extractor or pick to access the lock) and install the ones from your kit - simple press until clicks.

 

[Tricknine]

There 6 male pins on the subwoofer box and my new one does not have the wires in them so not sure of + or - on this. Also which wires do I tap at the ANC module

 

[Diamondback]

Did your rig come with the Base / Alpine / or HK?

 

[Tricknine]

No I did not I am trying to add the pen subwoofer to the 6 speaker system. I was reading on here in another forum where someone did it like this and they said it sounded really good so I thought I would give it a try. I have the 8.4 with nav but I am also in the process of upgrading to either the 8.4 or 12 with nav depending on if I can find a good deal. I did put a message out looking for someone on here if they one for sale.

 

[Tricknine]

Thank you very much for the diagram I just can’t hardly read the words once I zoom in on it. I will send to my laptop see if that helps.

 

[Diamondback]

SRy, I didn't realize the uploads posted them inline instead of attachments. PM me your email and I'll send direct if you want.

 

[Tricknine]

SRy, I didn't realize the uploads posted them inline instead of attachments. PM me your email and I'll send direct if you want.

[email protected]

 

[Tricknine]

Please send it I would like to try and wire it today or tomorrow thank you.

 

[Diamondback]

Sent -- you may need to save locally first (as with the ones posted above), then use your fave editor to zoom in.

 

[St-na]

Please send it I would like to try and wire it today or tomorrow thank you.

Did You managed to connect? I am thinking about the same solution.

 

[Tricknine]

Yes I did and it did help with the bass it does sound a lot better

 

[St-na]

@Jimmy07 do You know where to get 6 pin connector for Alpine subwoofer and how to hook it up to 2 pin aftermarket sub directly, without amp? Thank You!

 

[ekaz]

@Jimmy07 do You know where to get 6 pin connector for Alpine subwoofer and how to hook it up to 2 pin aftermarket sub directly, without amp? Thank You!

Not sure it'll have what your looking for, but here the site to get the part numbers to repair the connectors: http://connectors.dcctools.com/home.htm

 

[St-na]

Not sure it'll have what your looking for, but here the site to get the part numbers to repair the connectors: http://connectors.dcctools.com/home.htm

Very good, thank You! Mopar 68186565AA.

 

[Tricknine]

The connector Mopar 6pin harness is 69030094AA this is for subwoofer 68277288AB the you wire in to t taps on the Black connector anc module under the drivers seat PIN number #5 and #13 that’s the left rear + & - that’s the way I was told to do it and it does sound pretty good.

 

[St-na]

The connector Mopar 6pin harness is 69030094AA this is for subwoofer 68277288AB the you wire in to t taps on the Black connector anc module under the drivers seat PIN number #5 and #13 that’s the left rear + & - that’s the way I was told to do it and it does sound pretty good.

Ok, 69030094AA is a male for Mopar 68186565AA female (fitted on sub), If I follow attached drw correctly, I can hook up to any pairs: 1-2, 3-4, 5-6. https://www.ebay.com/itm/233661154960?hash=item36674a4690:g:sqQAAOSw03lY55a~

 

[Tricknine]

Pin 13 & 5 are at the Noise cancellation module under drivers seat it’s for the left rear speaker coming from that black plug. you twist 3 wires to the negative and the other 3 to the positive