5thGenRams Forums

Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

Rough Country M1 adjustable leveling struts

jl13

Ram Guru
Joined
May 28, 2021
Messages
1,102
Reaction score
968
Location
boyle heights, CA
this seems to be new.
Mostly 2" and under a lot of people keep the stock uca's but the mopar 2" lift uca's are the most inexpensive out there and have more travel angle than the stock uca's
 

Talon4U2NV

Active Member
Joined
Mar 4, 2022
Messages
198
Reaction score
92
Location
Bellevue, NE
Just installed on my half ton; paired them with a set of V2 monotubes in the rear and swapped my rear springs (Laramie, no Ram Box) to a set of Ram Box ORP springs. truck feels nice and tight, will be getting aligned tomorrow and the 295/60R20 Toyo AT3 mounted as well. Only a few miles on them so far. But truck feels firm/tight. Doesn't seem to waller around on bumps anymore either. No long term here yet, but i'm happy so far. Install was a breeze.
 

Talon4U2NV

Active Member
Joined
Mar 4, 2022
Messages
198
Reaction score
92
Location
Bellevue, NE
Here she sits. 2” M1 front. ORP Ram Box springs in rear for an inch. On 295/60R20 Toyo AT3 rubber. I do have a 1/4 spacer as well. Only bent the Mopar bracket for the front flaps a touch on the insides. Rides great!


3146c41bac2e0629cf7ad23dd77da223.jpg

2bb4b863f514bda3c624a01b48f6dab2.jpg

3b4ac3e6699377f370840dbeb5fa17a4.jpg



Sent from my iPhone using Tapatalk
 

Unclepoot

Active Member
Joined
Feb 4, 2022
Messages
94
Reaction score
167
Here she sits. 2” M1 front. ORP Ram Box springs in rear for an inch. On 295/60R20 Toyo AT3 rubber. I do have a 1/4 spacer as well. Only bent the Mopar bracket for the front flaps a touch on the insides. Rides great!


3146c41bac2e0629cf7ad23dd77da223.jpg

2bb4b863f514bda3c624a01b48f6dab2.jpg

3b4ac3e6699377f370840dbeb5fa17a4.jpg



Sent from my iPhone using Tapatalk
Nice! I ended up going with the Bilstein 6112’s and 285/65/20’s on a 0 offset. Looks good!
 

Talon4U2NV

Active Member
Joined
Mar 4, 2022
Messages
198
Reaction score
92
Location
Bellevue, NE
Bilstein makes good stuff. I went RC to give them a go. I plan to do Carli. But after the HVAC replacement and such it wasn't happening and my tires were toast haha. So far, Kit is great and no issues. Rides nice, Firmer and more sporty feeling. But not harsh. Some of that is being on a Load E tire...not at all uncomfortable though
 

BillD

New Member
Joined
Aug 27, 2023
Messages
3
Reaction score
0
Just installed on my half ton; paired them with a set of V2 monotubes in the rear and swapped my rear springs (Laramie, no Ram Box) to a set of Ram Box ORP springs. truck feels nice and tight, will be getting aligned tomorrow and the 295/60R20 Toyo AT3 mounted as well. Only a few miles on them so far. But truck feels firm/tight. Doesn't seem to waller around on bumps anymore either. No long term here yet, but i'm happy so far. Install was a breeze.
did you add the 1inch in the back because the 2inch M1s would sit higher in the front than your stock back?
 

Users who are viewing this thread

Site Vendors

https://www.jasonlewisautomotive.com/
Top