Bed organizer for recovery gear

[springman30]

I have seen bed organizers like this:

Bedside Rack MOLLE Panel System | Ford F-150, Raptor & Lightning (2015 - BuiltRight Industries

The best alternative to truck storage with the BuiltRight Industries MOLLE Bedside Rack System. Using factory mounting points, this no-drill system installs to keep your gear organized, easily accessible & secure. Lifetime Warranty, Made in USA.

www.builtrightind.com

Id like to have something similar for mounting recovery gear like the Hi-Lift, Traxx, per tank, etc. Does anyone know a manufacture that makes something similar?

 

[tobyw]

Those are cool, but kind of expensive for what it is unless you are dead set on utilizing the MOLLE system... Since these trucks already have a nice set of holes for the factory option cargo management system, maybe just use that as a layout for your own side rack made from something like 3/4" marine grade plywood, and just have it bedlined after your done getting it all setup with your gear?

 

[HotHareSpey]

Saw these at Home Depot for $40 a go. Very solid latches with locks. If you have a cover no worries. I’m picking up several. Water proof and washable. It’s where my gear is going

 

[TruckDriver]

In my thread here I went with the Husky 45L Box but I like that Milwaukee posted above - looks rugged + tons of tie down options.

I have that Dewalt posted above and it's too tall to fit under a cover, plus that suckers heavy on it's own, which makes it not very manageable by one person when loaded.

Another consideration; the Husky 45L can fit on the backseat floor with the single seat up, allowing you to displace it from the bed when needed; and in the months since i've had it, I have done that at least half a dozen times

Tool / Gear / Recovery / Utility Boxes (VEDC)

I've been searching and looking to pick up some gear boxes for VEDC (vehicle-every-day-carry). Something possibly modular so there's an EDC box and a 'Trip & Trail' ready box I can just toss in. I've come across the Plano Sportsman's Trunk line (the 1819) With the short bed and a Lomax cover...

5thgenrams.com

 

[springman30]

I have seen bed organizers like this:

Bedside Rack MOLLE Panel System | Ford F-150, Raptor & Lightning (2015 - BuiltRight Industries

The best alternative to truck storage with the BuiltRight Industries MOLLE Bedside Rack System. Using factory mounting points, this no-drill system installs to keep your gear organized, easily accessible & secure. Lifetime Warranty, Made in USA.

www.builtrightind.com

Id like to have something similar for mounting recovery gear like the Hi-Lift, Traxx, per tank, etc. Does anyone know a manufacture that makes something similar?

I decided to make my own...
Its solid, and fully adjustable to what gear I am using. I will post more when I have finished it and its in use

 

[TruckDriver]

I decided to make my own...

I was literally looking at that thread yesterday and thought the same thing, I better get to fabbing up! Nice work!

 

[springman30]

Its rough right now, ill rhino line it later and put up some pics. For less then $250 I have both bedside completed, with plenty of extra material to redesign it for any situation or gear. Its removable, and it also locks to the truck, and locks gear(until I get a lockable bed cover).

 

[go-ram]

I have seen bed organizers like this:

Bedside Rack MOLLE Panel System | Ford F-150, Raptor & Lightning (2015 - BuiltRight Industries

The best alternative to truck storage with the BuiltRight Industries MOLLE Bedside Rack System. Using factory mounting points, this no-drill system installs to keep your gear organized, easily accessible & secure. Lifetime Warranty, Made in USA.

www.builtrightind.com

Id like to have something similar for mounting recovery gear like the Hi-Lift, Traxx, per tank, etc. Does anyone know a manufacture that makes something similar?

.
Not the same thing, just tossing this out there in case it might suit some needs:
.
https://decked.com/products/decked-ram-1500?variant=13489340743746
.

 

[AnthonyD1978]

Its rough right now, ill rhino line it later and put up some pics. For less then $250 I have both bedside completed, with plenty of extra material to redesign it for any situation or gear. Its removable, and it also locks to the truck, and locks gear(until I get a lockable bed cover).

love it. Very well done.

 

[Leif_Ram2019]

I've thought about building something like this too, as there doesn't seem to be anything marketed for the 5th gen yet. But after seeing how much work this guys put into his, I will wait and gladly pay $295.

How To: Bedside Utility Racks

So I'm starting a project. I want to increase the utility off my bed by adding some bedside racks to the inside walls. I want to be able to mount a shovel, axe and other things in there under my tonneau cover to keep in there all the time. My plan is to use 1/2" HDPE and cut out holes in a molle...

www.ramforum.com

 

[Atlantic Blue]

 

[Atlantic Blue]

I had the undercover swing case on my 4th gen. A lil pricy but very useful.

 

[Atlantic Blue]

Craftsman 20 gallon tote

 

[orange01z28]

I like the idea of a tote

I also want to get a Hi Lift and one of these

LOC-RAC - Hi-Lift Jack Co.

Hi-Lift LOC-RAC Conveniently Mount and Lock Your Hi-Lift Jack to the Bedrail of your Pickup Model #: LR-200 Installation is simple. It can be mounted...

hi-lift.com

 

[Mitragliatrice]

Saw these at Home Depot for $40 a go. Very solid latches with locks. If you have a cover no worries. I’m picking up several. Water proof and washable. It’s where my gear is going

View attachment 42898

They also sell just the top plate you can mount somewhere for easy removal and secure latching to the bed in some way. The Packout system is pretty slick.