Air Ride Suspension Links Measurements

[eithkrp1]

I have the Revel LInks on my 2020 RAM Limited Air Suspension, and i want to be able to take the rear back to stock, and adjust the front to just a 1/2" up. Problem is the shop lost either the front or rear, so i don't know what the factory length is and not sure i can order replacements separately.

Does anyone have or can measure for me the length from the center of the fitting hole on the factory links? Or know where i can find it?

Thanks....

 

[Bpebler]

Could probably find it here:

My Maxtrac lowering installation

I haven't found a detailed thread with all the P/Ns and info in one easy to find post. Here ill post all the P/Ns, specs and links for the parts im installing. Most of this info is thanks to @Mopar_maxi Truck is a 2021 Laramie Sport, CC, short bed, 4x4,non ORP, with etorque. Suspension-...

5thgenrams.com

https://5thgenrams.com/community/threads/5th-gen-beltech-drop-spindles-now-available.43672/reply?quote=648933

@ferraiolo1, @Rock Crawler, @outnumbered, @1LowTrk all have good info posted in a few of the different threads on the 1st page of the suspension category in the forum here.

When is Mopar going to release a d*mn rear level drop kit to make life easier?! Sorry, I just ran out of patience over the years lifting my Cherokee several times. Looking for the easy way. Lol

 

[1LowTrk]

I have the Revel LInks on my 2020 RAM Limited Air Suspension, and i want to be able to take the rear back to stock, and adjust the front to just a 1/2" up. Problem is the shop lost either the front or rear, so i don't know what the factory length is and not sure i can order replacements separately.

Does anyone have or can measure for me the length from the center of the fitting hole on the factory links? Or know where i can find it?

Thanks....

Eithkrp1,

Attached to this reply you’ll find pictures of the factory links place above a tape measure.

One is 3.25 inches and the other is 3.75 inches.

Simply remove your revel links and adjust them to match the lengths shown in these pictures. I don’t have a caliper to give you exact measurements (center of eyelet to center of eyelet) for you but this should be very close.

***THIS IS A GUESS*** but I believe from factory, the larger links goes to the front and the shorter links to the rear.

 

[eithkrp1]

Eithkrp1,

Attached to this reply you’ll find pictures of the factory links place above a tape measure.

One is 3.25 inches and the other is 3.75 inches.

Simply remove your revel links and adjust them to match the lengths shown in these pictures. I don’t have a caliper to give you exact measurements (center of eyelet to center of eyelet) for you but this should be very close.

***THIS IS A GUESS*** but I believe from factory, the larger links goes to the front and the shorter links to the rear.

View attachment 136610
View attachment 136611

Thanks, that's a big help. Was the 3.25 and 3.75 from end to end? I did find one set, so i can match that up and then determine the which is which.

 

[Buz]

I saved my original links and they're labeled front and rear.
I can measure the rears later today if you want.

 

[1LowTrk]

Thanks, that's a big help. Was the 3.25 and 3.75 from end to end? I did find one set, so i can match that up and then determine the which is which.

I have pictures attached. It’s from end to end.

 

[eithkrp1]

I saved my original links and they're labeled front and rear.
I can measure the rears later today if you want.

Yes, please