Search results

Sorry can only be used in ram box models. The lock cylinder should be able to be rekeyed. The cylinder can be be removed by removing hex set screw on side of handle then pulling the cylinder straight out. Sent from my GM1917 using Tapatalk

Try putting flat head screwdriver under the screw head to pry out while unscrewing. Sent from my GM1917 using Tapatalk

Not sure what karr/wds is so I won't talk about that but sounds like forced dealer option(I steer clear of these type of dealers) . I personally don't take issue with t-taps, I rather use them compared to some other more destructive methods to the harness. The problem isn't with t-taps but the...

Congrats but your still part of the RAM family.[emoji16] Sent from my GM1917 using Tapatalk

Perhaps drilling a hole on the side of the frame is your best bet Sent from my GM1917 using Tapatalk

Best way is check your build sheet(not window sticker) . It will tell you everything that was put in your truck on the assembly line. Search the forum for the website address and insert your vin#. Sent from my GM1917 using Tapatalk

Due to chip shortages they moved some option availability to higher trim levels only. Sent from my GM1917 using Tapatalk

Got the same lights, one light must have a bad seal because water got inside and lense is cloudy after less than a year. Not too upset as the OP mentioned they were around $18. I guess you get what you pay for... Lol. Sent from my GM1917 using Tapatalk

Yes the Curt Harness connects to the 7 pin behind behind the bumper. I used it with with my opt7 light bar. Sent from my GM1917 using Tapatalk

Do you have 2019 classic(4th gen) by chance!. They have Studs from the factory like the 5th gens do. Sent from my GM1917 using Tapatalk

Definitely not factory... Lol, typical dealer scam! Sent from my GM1917 using Tapatalk

I would suspect the textured upper piece on Rebel would be a pretty good match for the aftermarket grill. Sent from my GM1917 using Tapatalk

I was saying my grill led's come on only when the parking lights are on, if you want your grill led's to turn on all the time"ignition on" then you can run wire wire and go into F38 using add-a-fuse. Sent from my GM1917 using Tapatalk

Only when lights are on, if you want them on all the time the ignition is on you can tap into F38 using a add-a-fuse. VideoPUP Car Add-A-Circuit Fuse TAP MICRO2 Adapter, Fuse Tap Fuse Holder and Low Profile Blade Fuse Holder for Cars Trucks Boats(10pcs 15A Fuse Plug + 5pcs Fuse)...

Thanks for the info. I did LED lights in my rebel grill and for me I ran a wire to back of the rear bumper and taped into the running/parking lamp of the trailer connector. I had installed the Curt t-harness for my tailgate bar so I used t-tap into curt harness but you t-tap into trailer...

Looks Good[emoji106][emoji106][emoji106] How's the overall fit and finish compared to oem? Looking at the pics of the grill on ebay it has a hole in honeycomb towards the bottom, what is the cutout for? Sent from my GM1917 using Tapatalk

https://5thgenrams.com/community/threads/2021-night-edition-third-brake-light.24560/ It can be added to 21 models, Check above thread for all details. Sent from my GM1917 using Tapatalk

If both being yellow causing confusion perhaps spray one of the caps with different color plasti-dip (or paint) Sent from my GM1917 using Tapatalk

Just curious what kind of tray was installed that need taillights installed. What is UTE? Did you have halogen taillight and they swapped out for led's???.... If so installing resistors should take care of fast flash and bulb out warning. Sent from my GM1917 using Tapatalk

I'm curious what they have to say about the notch on the grill bezel. If you enlarge there pic from there website you clearly see where they photoshopped out gaps between the hood and grill as well as the grill bezel notch. I would love this hood and would have no issue fitting and painting but...