Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
Well after all the warnings I’ve seen on here my pedal commander died on me in the worst situation. Driving on the highway in a construction zone during rush hour with no shoulder to stop on. Every light on the dash came on and I lost all throttle response. I didn’t know what was happening so I...
I went with the v6 for mileage and cost of the truck. I then got the “itch” to make it look like a truck. I now get mid 16s for mpg, but at this point it’s worth it just for the look. Wish it was a hemi, but for what I use it for it works
Mine appeared the same time as this: kinda weird that I’m getting updates on the 12.1 that I put in in place of the original 8.4. The same day this happened I lost my performance and off road pages too.
I just jacked up the rear from under the axle and then set the jackstands on the frame so the tires where just off the ground when I removed the jack. Swapping the shocks was simple other than the top bolt on the drivers side because there is less access around the filler neck. It took und wet...
I run 20x10 -18 on mine with 35x12.50 tires with a 3.5” lift. It required a little bit of mod to get rid of the minor rub I had, but now I have zero rubbing
It can be made to fit. I was able to get my 35x12.50 bfg ko2 on a 10” wide rim in the stock location, but I had to trim about a 1/4” or so off the back of the hitch. Basically trimmed right up to the weld. Without trimming it forced the tire to rub the trac bar and every time the truck moved...
This was sent to me and it worked:In alfaobd, go to CustSetMenu 1: Navigation Turn-by-Turn CSM Present- YES. Reboot the radio twice by holding power down about 10 seconds and the option should show up in settings. Mine is working now with native gps and apple maps as well. Thanks to @Jimmy07
Mine have the angle as part of the link itself. The top and bottom only have a washer and nut as loose parts not connected to the link itself when installing
When it’s making the noise try turning your wipers on and see if it stops. I have a similar noise on mine that’s not nearly that loud and I can’t find it, but I noticed it stops when the wipers are moving. If that doesn’t work try unplugging the factory amp under the drivers seat to eliminate...
When I did my bed lights I tapped into the 2 wires at the rear of the truck rather then running all the way to the bcm. Now I was reading that some are replacing the tail light jumper harnesses with 68488851AB and 68523847AA and then plugging in the bed lights. A friend has a ram with halogen...
I put a stock hemi exhaust on my v6 and then welded in a paradox muffler but kept the resonators in place. I later took it off and put the stock hemi muffler back on because the drone on the highway bothered me. I can’t find the clip of me reving it, but I have one of it on startup but can’t...
Finally installed the suspension maxx links today. No more clunk and the squeak went away. The lower joints on the stock ones were both really loose, but couldn’t tell how bad they were until they were off.
I called and they said if you use them as they come out of the box they will cause the front to be too high, but if you lower them 1 notch you will get the same lift as the v8. I’ve had them on my truck for about 8 months without issues, so I guess they do work. I gained exactly 3.5” with...
I did the m1 lifted struts on mine and their tech support suggested I lower them by 1 notch. I was told the n3s would lift an extra half inch which would cause issues with the cv angles. After moving it down 1 notch I got exactly 3.5” of lift.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.