5thGenRams Forums
Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!
New 2025 Limited - Must have 1st Mods?
- Thread starter Jszlaga
- Start date
Jako
Spends too much time on here
License Plate Reverse light
I did LED bolt lights. Definitely brightened it up, clean look, and doesn't interfere with the tailgate.
5thgenrams.com
Reverse light mod
Due to the poor lighting with the LED reverse light, I tried this today and pretty happy with the results. Let me know your thoughts... thanks! I don't plan on towing and if I have to, then it can be easily removed as I have installed quick disconnect connectors on the wires. The hardest part...
5thgenrams.com
Another reverse LED idea
I just fixed the one area of this truck that bugged me. The reverse lights are too dim and I could barely see the curb when backing up. I bought these Soundoff Signal 4" LED pods. These are white only but they have 2 and 3 color models since they're designed for police cars. I didn't want to...
5thgenrams.com
OEM LED reverse lights are absolutely terrible...what have you guys done to address this?
Finished, these are the Rigid Ignite diffused. Made a big difference! Really would like to see how you mount those on bumper in daylight. Thanks.
5thgenrams.com
LUYED LED- New (Frugal) LED Reverse Light.
LUYED Reverse Light EDIT: Install instructions provided by the manufacture LUYED. Please install however you see fit. 
Tapped into the 7 pin with supplied T connectors. 3M taped (supplied) to the bottom of the receiver. Install: -Look at your 7pin and look in behind your...
Tapped into the 7 pin with supplied T connectors. 3M taped (supplied) to the bottom of the receiver. Install: -Look at your 7pin and look in behind your...
5thgenrams.com
Hope it helps!
5thgenrams.com
5thgenrams.com
5thgenrams.com
5thgenrams.com
5thgenrams.com
5thgenrams.com
...
Choosing Best Tonneau Cover
If anyone is looking for the Truxedo sentry CT, Truxedo has a 75 dollar rebate till the end of the month I think. And if you call Luke at Truck alterations he’ll set you up with $750 shipped. After rebate $675. Not bad. Wanted to try something else other than a tri-fold that didn’t break the...
5thgenrams.com
Tonneau Cover Pics
I am looking for a cover and would love to see some pics of what everyone has and their pros and cons. Thanks.
5thgenrams.com
Tonneau Cover advice
I have attached a couple of pictures, I believe that you should be able to see were the cables are the one picture with the tailgate down. Let me know if you should have any other questions. If you are wondering, I do have a BedRug liner ordered, hate having a bare bed. Hope these pictures help.
5thgenrams.com
Retraxpro XR vs RetraxONE XR which one?
Looking to purchase a RetraxPro XR or the RetraxONE XR. Looking for a top with tracks to make it more versatile. Anyone purchase the RetraxONE and have regrets on not buying the RetraxPro or vise versa? Thanks
5thgenrams.com
Tonneau Cover Leaks on 2019 Rams
@Patsy1099 @YoAdrian Maybe you guys can help me with this - installed my sentry CT today. The instructions on installing the tonneau itself on the tracks are crap. Does this gasket on the front of the cover go above the seal on the bulkhead like in my pictures or should I have folded this...
5thgenrams.com
Bak Revolver X4 Poor Quality
$1500 cover and look at the horrible quality. I even cut myself on the edge! Misfit rails, horrible gaps. Seals missing or in the wrong place entirely. Nothing aligns. Buyer beware!
5thgenrams.com
If you are over 6'0" (I'm 6'4"), I highly recommend these as you will never again go back to a stock seat setup:
desertdoesit.com
RAM FRONT SEAT JACKERS® (1500)
Seat Jackers™ – Comfort. Control. The Way It Should Be. Stock seats don’t fit everyone the same way. If your ride leaves you feeling stiff, cramped, or just off, Seat Jackers™ fix that. Made in the USA from premium materials, these seat spacers let you fine-tune your driving position by lifting...
desertdoesit.com
Jako
Spends too much time on here
I wouldn't say leave it stock but I would say take some time and educate yourself on what is available, evaluate your needs along with your desires to prioritize spending some $$$$.Awesome. I recommend to leave it stock. That’s how I roll! Enjoy and good luck
Last edited:
Gren71
Well-Known Member
Helwig rear sway bar set to the middle hole so it’s just slightly stiffer… takes a lot of of the body roll out and makes driving just infinitely more enjoyable
Center console safe
Weathertech floor mats
Mopar front/rear mud flaps
Rear wheel well liners (if you dont have them)
Center console safe
Weathertech floor mats
Mopar front/rear mud flaps
Rear wheel well liners (if you dont have them)
Gren71
Well-Known Member
I just ordered these last night after being frustrated that I still can’t find the perfect seat position after 30,000 miles…If you are over 6'0" (I'm 6'4"), I highly recommend these as you will never again go back to a stock seat setup:
RAM FRONT SEAT JACKERS® (1500)
Seat Jackers™ – Comfort. Control. The Way It Should Be. Stock seats don’t fit everyone the same way. If your ride leaves you feeling stiff, cramped, or just off, Seat Jackers™ fix that. Made in the USA from premium materials, these seat spacers let you fine-tune your driving position by lifting...
Window tint, to include full windshield.
Dash cam(Fitcamx) to CYA.
Tonmeau cover of your choice
Spray in bed liner if you don't have one.
If you like performance the JB4 tuner seems like a good addition on for the Hurricane. and can easily be removed for dealer visits
Dash cam(Fitcamx) to CYA.
Tonmeau cover of your choice
Spray in bed liner if you don't have one.
If you like performance the JB4 tuner seems like a good addition on for the Hurricane. and can easily be removed for dealer visits
Jako
Spends too much time on here
For those considering running boards here are some "Factors" for consideration.
Factors for running boards:
1. material - steel, SS, alu, plastic
2. shape - flat, round, oval, trapezoid, other (more off road)
3. width - 3, 4, 5, 6 inch
4. color - black, polished, painted
5. connections to vehicle - brackets (no covers / covers-beefier look)
6. connection to vehicle - gap from vehicle, height from ground
7. ends - capped (plastic) or welded ends
8. ends - straight or "bent"
9. company - USA, dealer network, contacts (email, phone), warranty, service, reliability
10. price -
Maybe it will help in the decision process for those choosing other than Mopar.
FROM:
Factors for running boards:
1. material - steel, SS, alu, plastic
2. shape - flat, round, oval, trapezoid, other (more off road)
3. width - 3, 4, 5, 6 inch
4. color - black, polished, painted
5. connections to vehicle - brackets (no covers / covers-beefier look)
6. connection to vehicle - gap from vehicle, height from ground
7. ends - capped (plastic) or welded ends
8. ends - straight or "bent"
9. company - USA, dealer network, contacts (email, phone), warranty, service, reliability
10. price -
Maybe it will help in the decision process for those choosing other than Mopar.
FROM:
StealthTech6
Active Member
- Joined
- Apr 5, 2019
- Messages
- 61
- Reaction score
- 24
- Points
- 8
Are these the correct part numbers for 2025 with flares? A few sites I've checked and they appear to be the correct ones. Wouldn't mind if someone could confirm if they have already purchased?
82219131AA - front
82219070AA - rear
82219131AA - front
82219070AA - rear
I believe you will be very happy with them. I have had them in my Rams for 10 years and will never drive again without them. These make long drives very comfortable and short trips a joy.
Users who are viewing this thread
Site Vendors
