Search results

ahh I could not find the harness so I went the hard route. First time ever doing a repin. I still do not know the "real" way to release the pins as I was just able to use a screw driver and tug a little. May I ask where you got the harness?

Did you have to repin the cable? I am doing same install now and am unsure of the repin.

This is my next project. I am coming from an 8.4 Uconnect 4 to a 12inch Uconnect 4. I have searched and need some help lol. Since they are both uconnect 4, do I need any special cables or do I need to repin anything? Do I need to alfapbd other than: ICS Intergrated Center Stack: Not Enabled...

And solved! Sometimes a night of sleep is all you need. I found another thread yesterday with the same issue but his solution didn’t "seem" to work for me. ABS>DT 2019+> ECS In Plant Mode> Disable ABS>DT 2019+ > EPB In Plant Mode> Disable BCM> MY2020>Chassis- Electonic Parking Brake> Yes ABS >...

I followed another guide but I do can't seem to find this option: BCM> MY2020>Chassis- Electonic Parking Brake> Yes

I mentioned in the 1st post I did not back up. Lesson learned.

I just went out to take a look after like 25 and its still the same error and clearing it brings it right back. I will have to check tomorrow morning. Thanks

I adjusted based on mm but then reverted back to the original size I had before I started all this.

*** Solved and solution is in post #9 *** Special thanks to Daverous for his fix over 2 years ago. Hoping someone can help me on this one. I spent over 5 hours tonight in alfaobd trying to fix the issue. This all started with a simple tire size change. Next thing I know I had errors...

ok, so I am looking at doing this whole process. I have a 2020 Ram Bighorn with the 8.4. My old truck had the 12" and I just cracked my screen. Any suggestions on doing this upgrade? I looked on ebay and noticed some radios say "locked". Does that mean I need to install and take to dealer...

I found a guide on youtube and I think its fixed. I tested on a normal drive but not a parking lot yet. Anyway, I took the front mudguard off, trimmed like 2 inches of the plastic that goes into the little bracket (that plastic fastener goes into) and then I bent the bracket up. I did hit...

Been awhile since I posted. I have a 2020 Ram 1500. It was not new when purchased. It had 33in tires on it but the other day I was out and knew that at some point I would need new tires and figured I would stop into the tire place. fast forward, I walked out with Toyo Open Country A/T III's...

Thanks!

I removed it because after the new bumper, you could clearly see it hanging there. Just looked really strange.

I have a 2 hour drive today and will be doing highway miles at about 75. It will be a good test and will report back. I have been on the highway since removing but never noticed. I will turn the radio down even to see if I hear/feel anything.

Nope, nothing to report. Gas milage is the same 14.1 mpg. Handling is fine, and no errors :) I just listed my airdam even since there have been no issues.

Thanks, I was on the fence.. I will run the actual switch to turn it off/on into the cab.. It will be done correctly atleast.

Tap power. Basically, when I put high beams on, the light bar will come on. I hardly use high's but when I do, it would be nice for the bar.

2020 Ram Big Horn Has anyone done this? I tried to tap into wires that go into the high beams but that did not work. Can I tap into any of these wires? This is in front of the drivers side wheel. thanks

big horn fogs.. I plan on posting my 2020 big horn fog lights in a few days. I am in florida so dealing with this hurricane. I took the entire bumper off since I replaced the bumper. You can see my before/after in you look at my posts.. thanks Joe