Search results

I will post over at the bobistheoil guy forum. I'm sorta concerned about the test not being just a bad test because all the other numbers were good.. Just one item was very clear its raising a flag.

Finally got around to sending off one of my samples for a report. I've been consistent with changing the oil at 5k intervals. Running penzoil platinum or penzoil ultra platinum depending on what i could get at the time. Always ran a stock mopar filter. Iron and copper are higher than any...

yeah something seems off. I've never come across weight distribution setups reacting like this ever.

Kind of annoying to have to pay for a map update for a 2021 truck. Our other cars have updated for free from time to time.

Any idea where is this found in alphaobd, i have not yet located that setting.

I just checked mine. It was low. I've got 11k on the truck, 8.5k of that was towing my traving trailer. I topped it off with a little over a half quart before it started to overflow. I'll be doing a complete change with Redline next spring before i start dragging the trailer again...

Does anybody know if we need to update the ibs system charging to recognize a higher capacity agm is installed instead of the lead acid. Past vehicles i've owned required the ibs to be reset to recognize for a new battery or different capacity to charge it properly. The "intelligent" systems...

I run the propride hitch after wasting money and time on other hitches. Just about everything about this hitch is worth the money. Safety for my family being no. 1. Once you figure out the nuances of the system it is by far easier to use than any of the friction bar or chain based sway...

I finally installed my 33 gallon tank used the recommendations by jsandgren10 earlier in this thread using steel bar and the earlier bracket retrofit kit. It actually took me longer to fabricate the bracket and drill the frame than it did to drop and reinstall the tank. Was really easy...

Well this happened to me after 6k miles. It worked when i parked at the grocery store. Came out of the store and then it wasn't working. Tried the two reset methods. The only one that worked for me was to hold the tune & volume buttons down for 30 seconds while truck was in "on" mode, then...

I started at my tires max psi of 65 psi. for me it was a matter of letting air out long enough for the sensors to register something was happening, not so much the actual pressure.

For those that have done this. is there a trick to getting the fuel fill inlet off? I've crawled under and walked thru of all the steps before i start. I could easily undo all of the fuel lines clips and vent lines and put them back on. Everything is quick and easy except the fuel fill...

City/State: Jeff Belzer Ram Dealer Name: Lakeville MN Recommend: Hell NO! The sales experience was so bad i eventualy just walked out during the finaly paperwork as what the agreed upon price mysteriously went up for bs reasons. Laundry list of screw ups by sales team i finally lost my...

thats what i used. There is no known part number for the 1500 for the jumper.

I've finally got around to getting my trailer out of storage and getting the tpms sensors installed to finish the install. Got it all up and running. But be warned the instructions in the manual to pair the sensors are ineffective and did not work for me. The instructions said let 5psi out...

Oddly enought I have a 2021, but alfa obd did not havea a Body Computer my2021 yet, , I had to us Body Computer DT MY2019 Powernet Ver.4 to get the trailer tpms options options in alfaobd. oddly enought the alfaobd settings for DT MY2020 did not have these options in aflaobd.

it was real easy, you unplug the rear fascia harness from the left side harness and insert pins from the harness into the plug, then connect it all back up again. took 5 minutes. I forgot to take pictures when i did it as it went so quick.

I just went thru all this. Just waiting to get my trailer out of storage to get the tpms sensors installed to confirm once and for all its up and running. I've got all the menus on my evic and uconnect screen. It took overnight before the configurable options showed up on the uconnect...

Jimmy thanks, will take you up on that except its -5f here in MN. I am going to have to wait a month or so before things warm up enough work on this. Would the harness you make clip inline where the fascia harness and left chassis harness connect?