Search results

When an opportunity comes your way, you take it hahaha... That is exactly what I did. My buddy at work had his Borla warrantied because some of the pipes were bent. I asked him if I could have his old Atak (newer then my s-type) if Borla doesn't want it back. Well Borla doesn't want the stuff...

Hey I appreciate that. Hard to get shots from internet with good views. It helps also to see where your bar sits in relation to the bumps in the plastic bed caps. See if my bar will sit in the same spot or closer in. Can you a picture from further back showing this angle and the bar and maybe...

The bars ordered from dealer are installed different then the TRX. What you don't see in the pictures is a stake pocket mount. So on the bars you get from Mopar they are held on with 2 bolts at the back and then a bracket that bolts onto the side bars where stake pocket is and slides into the...

I don't follow sorry haha So if you see picture #4 where there is one bolt in a hole and then a shiny silver piece. That is basically a welded nut inside of the tune. I don't want to loose those threaded holes as that is where the bolt goes through the side bar tube and through the joiner plate...

So here is one of the middle bars. Picture #1 - shows the threaded bolts that goes into the threaded hole. I can't cut from the end because of the treaded hole and because the pipe needs to slide into the other bracket. So I would need to cut passed narrow part of the pipe. Cut out a section...

Yeah the 2 center bars are bolted where the collars are. Those are just rubber collars that go over the bolt holes and then a "joiner plate" slides under the rubber and bolts together. So both ends of the bar need to be cut on both front and back bars. The center tubes slide inside of the...

Just hope that cutting the bars doesn't pull the side in where they don't match up with the cab.

Well actually, before seeing these messages I was talking to my buddy about doing this. He is a welder and fabricator so we were discussing this. I may go this route, as these bars don't pop up often around me and when they do the sellers are asking $1000-$1400 for them. A little modification...

As far as I know there are only 2 different product l numbers. 82215959AC (1500) and 82215869 (2500/3500) Inside of TRX box is same as the 1500 as far as I know other members have gotten take offs from the TRX and put them on the normal 1500s. Needless to say I'm not happy. Was all excited...

Hey everyone, decided to post here in as the buy/sell is mostly US people. Selling a RamBar I just picked up that I was told was for the 1500 but in fact it's for the 2500/3500. Pictures show it's too wide. So from what I gather this bar will fit... 2019+ Ram 2500/3500 2010+ Ram 2500/3500...

Well apparently the bar I was sold is for the 2500/3500 models. Guy didn't tell me part numbers and I assumed it was for the 1500. A little too wide for full bar and feet are too narrow for the top rails. No part numbers stamped which sucks otherwise I could have verified. Anyhow, ended up...

Picked up this RamBar today for $650cdn ($500usd) , guy purchased new for $1200cdn to try on his DS but the top rails get wider on his box so it wouldn't work. I told myself if I could get the bar for a decent price I'm gonna get one, cause no way I was gonna pay $1000+ for a rollbar. Anyhow...

I have been going back and fourth on getting the RamBar for my Sport, sometimes pictures of it look funny and other pictures it looks good. It also for me, depends on the look of the vehicle itself. I think the the RamBar will be nice on the Pearl Blue especially with the lift and 35s on it...

Sorry for the very late reply, haven't been on much lately. I tapped into my bed lights that came with my BUG package for the running light and the turn signal wires for the turn signals. I didn't use the orange running lights but would have been wired into taillight running light wire...

Yea, that I already know because one of the bigger suppliers here where I'm at told me they have a connecting pipe as he called it, but it's smaller than the Atak muffler. Thus being louder, and I want Atak louder not louder then the Atak though. It doesn't make sense that they will not sell...

Does anyone know if you can order just the Atak muffler? I've contacted Borla and waiting for a reply. I've also contacted a local authorized dealer (the biggest one for Borla) and they can get me a muffler from Borla but much smaller and louder. You'd think you can get just the muffler...

Bringing this thread back up from the dead. Today I had the blue screen pop up from my camera (was fine this morning) and I was like WTF. Then I turn up my volume and the radio is also cutting in and out, doesn't matter if its AM, FM or Andriod Auto. Funny thing is, I've already had the radio...

Paid $100cdn ($75usd) to have my front resonator removed. Was about to drop $300cdn on the Corsa bolt on and or have the shop make me the same bolt on pipe for same price. Guy suggested cutting it and replacing as it's way cheaper. So that's what I did. Even if I want my resonator back on for...

I have since rebooted and reset my AAWIRELESS dongle. Everything is has been working for me and it's been a few weeks.

Today I removed my Westin R7 steps and replaced them with the 2021+ Ram Off-Road Steps which are hard to find. Got a good deal and didn't want to pass it up. I like how these match the pattern on the bumper steps as well. I really like these. I gained 2" from ground to bottom of steps and the...