Search results

IB, I had the same problem. I signed up on the notification on Bilsteinlifts to be notified when they became in stock. I got the notification about a week and half later that they were in stock and ordered them within 30 minutes of getting email. They are hard to find.

Jtimm, I am going to try and attach the installation instructions and there is a diagram on page 2 of 6. It shows installing the Bilstein spring seat adaptor. If you install it on a Rebel or other Ram with the factory 1" lift you will get this. Picture attached is when the guys installed the...

BlackBeard---- Trucks look great,

I set mine on 5 for the Rebel. I'll have to check again, but I think the top edge of my fender over each wheel is 41.5" That is front and back

I know this one should get some laughs, but it was a kick driving and a great sleeper. I installed the TRD supercharger at 31,000 miles and it was still running strong at 144,000 when I gave her up. I never did put any drag radials like some of the other guys. Just regular tires. 13.3 @103 was...

I ordered through Bilsteinlifts.com. Chatted with an agent and informed them of what I was looking for. They were backordered so I got on a waiting list. Week and a 1/2 later, I got an email that they had received 8 sets and to order quickly if I wanted them.. 2 days later in my driveway. THIS...

I have the 2019 Rebel and I went with the 5100's to keep the geometry close to the same. The 5100's do not change the geometry as much as a leveling kit does. I have them set on #5 If you look at the pictures below, the one on the left is with the 5100's installed properly. The picture on the...

Yes, the interior fan. When I kick it up, as you mentioned it apparently kicks up the fan speed at the radiator up. I know when I stop and kill the truck it sounds like a jet engine winding down.. Seems to bring temps down for me when I do it. May not work for everyone, but I've done it often...

I'm glad you all brought those temps up as ok.. I drive a 895 mile trip to W Texas from S Louisiana and I see temps up to 226 while on cruise at 80. If I kick a/c fan up to 6-7 speed my coolant temps drop off quick. I seen this before, but had forgotten upper limits on temp. I tow a 22' bay...

SNWJNKY, so we have 14mm x 1.50 threads on our trucks... I like these you sent the link to.. Think I am fixing to slam the button on them. Thanks for the information Gorilla Automotive 96644BDX Black Factory Style Wheel Lock System (14mm x 1.50 Thread Size, 24-Pack)

Do you have the part number for these? Is there a locking lug mixed in with those? Couldn't tell from the picture. I think those look a lot better than the ones we have standard on the Rebel. I need to change mine as well to this style Thanks for any help.

Do you think the Rebel sway bar would be the same diameter? I'm going to try it. I drive a lot of lease roads in W Texas and they are nasty to say the least.

https://www.prothanesuspensionparts.com/191503. The Prothane website has them listed for $20.97 for the set. Looking back at site, this is the one without greaseable zerts on the mounting bracket. Universal - Greaseable Sway Bar Bushings - 35mm (1.37 inch) Manufacturer: Energy Suspension Part...

I have the 2019 Rebel and my mileage is a little over 50,000. I have had the truck aligned twice. One of those was after adding the Bilstein 5100's to the front to level it out. I have not had any problems with getting truck aligned. Nothing special was required.

Every once in a while, I will attempt to unlatch and it will not open. A slight push forward and it pops open. 2019 with a little over 50,000 miles.

I work 14 x 14 in W Texas and travel the lease roads. I have the MX4 and it got full of dust. I went back and put seals on the side as well as covered holes at hook attachments. I also bought the seal that goes across the bottom. It helped a lot. I still get a little dust, but not much.

I know when I ran them pretty regular with the 150 watt linear, the radio shop told me I needed to get the base on top of the truck. Working with the roof line gave you a better ground plane to work with. It was hard to get my swr's down low when I had it on a tool box or on the top edge of the...

We guys have been working on this a while. We all have a little bit different material, but basically work towards the same goal. Keeping as much water out of the bed as possible. It seems like I have tried everything, but I know there are some more ideas coming in with the fresh group of eyes...

I totally agree, and my meaning was not to say they were doing anything illegal, its just as you said (There is a supply and demand problem right now) When the Demons came out on the lot, they were marked up above retail due to limited quantity and that was totally expected, but I just haven't...

Just saw trucks for sale, 1 a fully loaded out Laramie with every option including HUD. When you click on view window sticker it is $68 and some change, They have it listed at $71 and some change... Wouldn't that fit into price gouging?