Search results

From an earlier post "The 5 choices are 68523482AA, 68523474AA, 68523477AA, 68523479AA, 68523472AA. : Console Wiring" I bought 74. It included the heated/vented switch connectors, two115V connectors, and an extra 12V connector..

See if you can read this one. Also, I have XY430 and 435 connectors, and pins for one of them. I see it truncated some. On XY430A, Pin 1 goes to XY331A Pin 23, then to Assembly-Power Distribution Center C3 Pin 32. Pin 9 goes to XY331A Pin 54, then to Assembly-Power Distribution Center C3 Pin...

Just so pumped that the right switches work! Have ordered another left switch; and hoping both sides will work..

Swapped upgraded rear seat (reclining) into my 2022 BH. Everything works; but I don't have the posts (pins)i n the rear wall to attach the 'close out' carpet piece. I've searched thoroughly in all the rear seat catalog pages and can't find anything. Does anyone have a PN? Thanks.

Thanks. I got around 12V on both the Fused B+ and LIN BUS on both connectors; with respect to each connector's ground--so it seems all 3 pins on both connectors are OK. I even verified the pinning on the Right connector just in case it was made wrong. I couldn't swap the switches because of...

I have a 2022 BH with Level 1 EQ. Last year, I swapped in Heat/Vent Front Seats and Heated Steering Wheel. They didn't require programming to get the hard buttons to work. I have now programmed them with Alfa and the soft buttons now appear on the display. I just swapped in Heat/Vent Rear...

I've made a lot of progress; but have one issue remaining. My truck, 2022 BH with Level 1 EQ, had none of the wires for the rear (also had none for the front) seats. I built a harness with XY430 and XY435A. 6 wires interconnect these 2 connectors. Also had to run 3 Fused Ignitions, 3...

Today's update, and to help my thinking. There is 12V at both the Fused B+ and the LIN BUS pins of the Left seat switch connector. With reference to ground pin in the connector, so apparently the ground is good. I think the LIN BUS is supposed to be around 12V when resting, and sends out a...

Thanks.. I don't totally understand all of them; but doesn't seem like there'd be any value in running this wire to the center console plug (for future mods). The connector, and same description except C2, plug into the Interior Fuse Box..

For sure. I feel somewhat optimistic since the controller is in the left side seat and at least it's communicating with the right side. I'll trace the console harness tomorrow. Can't imagine it doesn't split A207 and LIN BUS to both switches. Incidentally, there's another circuit in...

I see that setting now. Changed it to Programmed; but still have only Left side switches working.

Operator error! There was no voltage on Pin 3 of XY360A. I traced it back. Last year, when I had run the A207 RD/GR to ASSEMBLY-POWER DISTRIBUTIONCENTER-INTERIOR C1, pinned it incorrectly. I didn't miss it by one pin--I was way off. I repinned it correctly to Pin 24 and voila had 12V at...

Thanks. I just tried it. It was already set to 3 Level. Maybe when I set Seats A-Rear Vented (and Heated) Seat Levels both to 3 Level it also updated the Configuration setting? I have verified 12V at each of the 3 Fused Ignitions on XY430A and the one on XY435; and that the 3 grounds are...

Were you able to make them work? My 2022 BH did not have the wiring in the truck; but I have now built and installed the wiring. I have make these changes, and nothing: 1. ECUConfig 4-Heated Seats Present to YES. (this one is confusing; ECUConfig 3 says Front Heated Seats present; but 4...

I robbed the IP ambient light wires from the donor harness and rebuilt them into my truck. Added the 3 IP lights, replaced the footwell lights and replaced the headlamp switch (2 wheels and rear fog light function--I'm optimistic). Did the Alfa changes ECUConfig 4: Ambient Dimmer: No => Yes...

I agree. I like the one over the glove box; but the two on either side of the cluster are not much. I saw in FM45's write up about reforming the trim pieces to allow more light to come through. I can't imagine the plant did any finessing like that..

I tried sliding it it; but decided to remove the glove boxes--just a bunch of screws. Once I understood how the light tube is secured (the tab on the end of the tube has to go past the "ear" molded into the IP) I might have been able to manipulate it in.

I should have listened to you. But, I had the harness and decided to do it. The one over the glove box is nice; but the 2 on each side of the cluster are worthless. I saw in FM45's write up that he reformed the two trim pieces. If the plant had to do this, that's probably why the option was...

NEED HELP. 2022 BH. I completed harnesses to XY430A and XY435A and have make all the connections. I flashed ECUConfig 4-Heated Seats Present to YES. (this one is confusing; ECUConfig 3 is Front Heated Seats present; but 4 doesn't say Rear, just heated seats) . Also flashed Memory Rear Heated...

I finished and installed the harness I built. (This would have been so much easier to do the FRs and the RRs at the same time--but I don't think I knew RR heat/vent existed at that time) 1. PK/VT and PK/BN to XY331A. Surprised that F20 and F29 were present in the interior fuse box--for an...