Search results

Def think that's the error issue... you also may have to add two pinned wires from the wiring block under your drivers seat to the module in the kick... you can check if you need them by looking at the grey plug at the module and see if all cavities are full... 68360453AD --- this is the rear...

@vin56--- How many sensors do you have in the rear - 4 or 6... with the new module and the new setting change - the BCM maybe looking for the two extra rear sensors -- just a thought -=FM45=-

Another option -- used them a half dozen times... https://www.mycartrim.com/ -=FM45=-

More Complete info--- MOD 100% tested and working https://5thgenrams.com/community/threads/adding-front-and-rear-parking-sensors.23200/ -=FM45=-

Quick how-to.... Enjoy :) -=FM45=-

As promised -- The Write-up .... Be gentle :) Hope nothing is missed-- -=FM45=-

--- that is a two piece plug.. slide the two sides apart and see what side is missing--you'll either need the male or female ends... re-pin your wires and you should be up and running -=FM45=-

Rick-- Posted is the yellow plug being refereed to... this is the one from pass seat - drivers has the same ... XY410 and XY420 - locate them and check what wires are present or not ... as far as the leds you have in had, check the part numbers against the numbers that are posted - the posted...

@ Nick-- Yes -- done it to my Bighorn... doing all 4 doors in the near future... I will get a write up together... it's going to be a little... i got 3 write-ups ahead of this one ... This write-up from Paragoptics will show the placement of the dash leds---...

Now I'm at a loss--- you already have everything in place --- did you add them or were they already in place from factory.. If they are already there they should work as is... yellow is interior, wht/grn is ambient, and black is ground... Are the yellow plugs populated with the corresponding...

@ Rick-- Parts needed-- @ Under Rear Seats OEM 68367033AA qty2 Lamp Foot well Rear LED Mouser 571-1456983-1 qty 2 Connector Mouser 571-1670144-1 qty6 1.2 Terminal @ Yellow Plug Mouser...

Anybody wanting to do this, it "IS" possible to add the OEM ambient dash lights. Parts needed-- Led Lights- 68312667AB Qty 2 68291948AC Qty 1 Wiring Harness- A custom harness can be made by using 68340401AC -- this is for the door leds, but it was modified for use in this project.... The...

@K... It sounds like you are describing the rear harness.. the OEM rear harness, when equipped, will power the 4 or 6 parking sensors, the rear antenna for the keyless-go, not to mention the license plate lights and the trailer wiring... so ya it really does matter what harness you grab... If...

More info in this thread... because you have a single zone --- it will stay a single zone but you will have Auto Hvac, controls will show up on the 8.4... you would just sync the two sides.... for a true dual zone you would have to do modifications behind the dash.. yes removing it, way too...

@Y--- as far as the wiring for the front, I bought the OEM wiring harness that goes from a factory plug out to the Fog lights / Front sensors... I believe all Level vehicles are pre-wired to a certain point.. for ex. the front is wired from a plug on interior then out to a plug behind the...

I'm just finishing up this mod to mine, all OEM parts except for the 3 custom harnesses I had to make -- from module to factory plugs... if you have AlfObd, you won't need to make a trip to the dealer... -=FM45=-

more info--- https://5thgenrams.com/community/threads/floor-lighting-to-ambient-lighting.21053/ -=FM45=-

FYI---- wiring is NOT present... you would need wiring for each door, the 4 housing/leds, and the acrylic tube for the bottom pocket which you will have to make or source from a wreck...

OEM part numbers for dash and foot wells--- https://www.moparpartsinc.com/a/Ram_2019_1500-LARAMIE-CREW-CAB-57L-HEMI-V8-4WD/_52016_7561992/Lighting--Instrument-and-Body-Panel-Trim/i2381787.html -=FM45=-

Not sure if it's simply cutting a wire for a kill... but---- I believe Red is 12v ... just test-- -=FM45=-