Search results

@Rstan-- if you upgrade oem halogen to oem led, I think you flip the pins in your connectors.... first pic is base--second is prem... -=FM45=-

You can start here--- https://www.moparpartsinc.com/a/Ram_2019_1500-LARAMIE-CREW-CAB-57L-HEMI-V8-4WD/_52016_8238251/Display--Center-Stack/i2544636.html choose the bezel that fits your needs-- ** edit---- I have this in my garage, is this what you're looking for--- -=FM45=-

Colton--- Look at post #28 by Dj... you'll see a white piece of plastic with two holes... that plastic is were the light assembly mounts... -=FM45=-

Does this help ya--- -=FM45=-

@Trav--- I have not had a chance to look thru my toolbox but those pins look correct... the ground is already in both 410/420 plugs, you'll just have to tie into that wire... as far for the 370A, I did not use that for my signal.... connector C6 on the BCM has the wire that I used for the...

@ DJ--- I already have the led assemblies and most wiring for each door... I am adding passive entry at the same time so I only want to open the doors once... Covid has delayed some of my parts. There is one part which is not available from factory, the acrylic tube for bottom map holder.... I...

--- in your pic, if you notice the large yellow plug... the new light assembly will be wired to that... I can give you the pin outs to each side once you get the parts.. You will only need to re-pin two cavities but three will be used... the common ground will be re-used... -=FM45=-

DJ--- If you look under each seat, center rear location, you'll notice a piece of white flat plastic with two holes in it --- one hole is for mounting the other keeps the assembly square.... -=FM45=-

Here is a pic from the rear side of mine, .... (ending in) 1AC ---- I am sure the part you posted just superseeded mine, so essentially they are the same and should work as described.. you do have to make the change in the BCM so that the truck recognizes the new device. Alpha can do everything...

I added 12 volts in the bed area... Pics with a pdf write-up Hope it helps ya-- https://5thgenrams.com/community/threads/what-did-you-do-to-your-ram-today.1686/post-284210 -=FM45=-

@ DJ --- nice job on the lighting... looks bright... I know you added some interior lighting but can't tell from post or pics if you have the factory ambient lighting. The factory ambient are under the front driver and pass front foot well, under drivers and pass seat.... there are also two...

The panel switches look and feel like switches and knobs but they are sending data to BCM, that's were all the magic is done. One wire can send multiple commands from multiple switches/devices... You can't add wires and relays from these 'switches' ... -=FM45=-

If you are referencing the plug behind the head light switch and dimmer, I believe all wires are present-- you leave as is.... Look at the BCM and locate C6 and see if the wire is present... If it is, I think if you change the switch to one that has a dimmer/ambient knobs and make the proper...

My plug is exactly like the pic you posted... the wht/gn wire is the ambient wire but you don't pick it up at the switch itself; our trucks use mux/data/resistance to send multiple info down one wire -- network like. You need to find the body control module, drivers side kick upper towards...

Go here--- https://www.moparpartsinc.com/a/Ram_2019_1500-LARAMIE-CREW-CAB-57L-HEMI-V8-4WD/_52016_7588023/Switch--Headlamp/i2381462.html you will see 4 listed, the key is look for overhead cupholder lamp... that lamp is controlled by the ambient dimmer switch.... So your truck doesn't have the...

@T32--- I am on duty for the next 24 so I little patience, I am digging up what I can from memory... the ambient dimmer was already present in my vehicle and I picked up the dimmer wire from the factory plug if the ambient lights were present from factory. As far as the pins, I just re-pined...

Sorry for delay... some basic wiring knowledge is required for this mod. The old light assembly and connector must be removed and replaced with the new assembly and connector. Use the reference url posted for connector pin-outs, look at lamp footwell lighting basic/premium --- the basic is a 2...

I went the OEM way... you do have to remove the old light assembly and connector; install the new factory assembly, new connector, and an extra wire for the ambient side of the light... i added one under each side of the dash and one under each side of the front seats in the factory locations...

For those of you who wanted or were thinking of adding auto HVAC to your ride it is possible. I followed the posted video and just adapted it for the 8.4 radio. I needed to install the two sensors and change my radio shroud to have the Auto HVAC buttons. The final step was to add the function to...

AlfaOBD for pc or android, gateway bypass, and a OBDLink usb/bt module ... best bang for the buck--- -=FM45=-