Recent content by Grayman5752

  1. Grayman5752

    Are software updates part of PDI?

    Not sure man. Maybe it has to do with their warranty status. My dealership is a Premium status shop, so we have a lot more freedom in what repairs we can do without getting FCA’s approval or involvement. Sent from my iPhone using Tapatalk
  2. Grayman5752

    Are software updates part of PDI?

    Don’t know where you got this info from, but definitely incorrect. Any tech with an FCA log in and access to WiTech can flash a module. FCA just won’t necessarily pay the tech to flash it if the customer didn’t have an issue that the flash addresses. There are “essential” (recalls, rapid...
  3. Grayman5752

    Storage above 8.4 screen in rebel

    This is how I use it for now, til I find something better Sent from my iPhone using Tapatalk
  4. Grayman5752

    CHECK ENGINE LIGHT Ive lost count

    MDS lifters are cylinders 1, 4, 6, and 7. Sent from my iPhone using Tapatalk
  5. Grayman5752

    2019+ Rams with Lifts/Levels, and/or aftermarket wheel tire setups

    It’s a Limited that’s been de-chromed and the grille color matched. The “ducts” (don’t know what else to really call them) on either side of RAM in the grille are separated, whereas on a Laramie or Big Horn w/ sport appearance, they are incorporated to the perimeter of the grille. Sent from...
  6. Grayman5752

    What did you do to your Ram today???

    Tinted my tail lights with VHT nite shades. Couldn’t stand the red with the gray and black. I think they came out just right. Still need to wet sand them and apply clear coat but that can wait. Definitely going to do the third brake light too, just waiting until I get LED bulbs so I can do it...
  7. Grayman5752

    Frozen 12” screen

    After all the modules are reset, configuration restored, and the bus goes through a full sleep cycle everyone should be on the same page. If the font is different after all that, just go into settings > display > themes and change it to the one you want. You may have to let it go through another...
  8. Grayman5752

    Frozen 12” screen

    We’ve been seeing a lot of these 12” Uconnects coming in like this. Even after replacing the radio, they still act funny. We found the only way to get them working properly again is doing a reset of the SGM, BCM and radio with the scan tool, then allowing the bus to go to sleep for approx 15-30...
  9. Grayman5752

    Anybody running 285/55R22?

    I think they’re a good choice, just not a lot of people are running them. I love the look of the updated Mopar 2” kit with 35x12.5s but I also like a bit more opening in the wheel wells. Sent from my iPhone using Tapatalk
  10. Grayman5752

    Anybody running 285/55R22?

    Trying to decide what tires to run. Seems like most have 35x12.5R22 but I want to see if 285/55R22 is a size worth considering. I’m going to be running a Mopar 2” lift, so bonus points to those who have that combo.
  11. Grayman5752

    Pop noise when turn at low speed

    There is a TSB for replacing the body mounts. Fixed the one I worked on that was doing it. Sent from my iPhone using Tapatalk
  12. Grayman5752

    Just got a 19. Waiting for deletes and tunes.

    So far everything is still in production, as far as I know. As for the exhaust piping, a new downpipe from the turbo has to be made because of a change in the after treatment components. Where are you located? I have one of the best guys in the southeast in my “entourage.” Just waiting for all...
  13. Grayman5752

    Cold Air from Window Defroster with AC set to Face only

    FYI, it would be the mode door not sealing, not a blend door. Blend doors are for temp, mode doors are for vent position (face/floor/defrost). Could be taken care of with an actuator calibration test done with the wiTech scan tool. I’m in Charleston, SC, and haven’t seemed to notice much of an...
  14. Grayman5752

    Updated 2" Mopar Lift/Level Kit - Discussion

    Loving all the info on this thread and all the great looking trucks, especially @MagMan1379 because we have the same truck [emoji1303]. Still looks like there is a bit of a rake with the updated spacer... has anyone tried stacking something like a Motofab 1/2” level kit to achieve a more leveled...
Top