Search results

I lucked out on the positioning of the middle LED on the Driver's side. Seems it lights the area perfectly. The Passenger side not so good. It shines inboard too much. I need to remove the Passenger door panel and adjust the angle of the light.

As I recall, you just unsnap the bottom plastic layer from the upper. Also need to release the latch-since the latch ears also hold the lower layer in place. The wire for the light is plugged into a white "dummy" piece. Remove the dummy piece and replace with the black lamp.

I plan to order the 879 you listed. But still somewhat unclear. Catalog lists 879 as W/Auto Park 1500; Park Assist Module; Park Assist W/Stop Only and 880 as Park Sensor, W/O Auto Park 1500; Park Assist Module; Parallel/Perpendicular Ithink Auto Park means the truck shifting into Park...

I bought a used 68271822AI module; per FM45's writeup (didn't realize until now it is specific to 2019). I have completed installation of only the rear so far. I chose Rear for VehConfig1-PTS Config: I now get the icon in my cluster but it says SERVICE under the icon. Wondering if it's the...

Thanks, Brent Did you get an answer on the module PN?

Thanks.

Great, thanks. Yes, I'd like to see your list. From the HUSHAN site, I think I received two flavors of the same two bezels? HU-CRR017-BZ Ram Ram 2019-2023 Parking Sensor Bezel Front Center RH 68335621AC HU-CRR018-BZ Ram Ram 2019-2023 Parking Sensor Bezel Front Center LH 68335620AC...

I'm confused about the sensor brackets (bezels). FM45 said I'm confused about the sensor brackets (bezels, trims). FM45 said to use 68335619AC, 20, 21, 22, 23, 24.. I ordered a 4 piece (not sure why not 6) kit. It contains PNs HU-CRR017-BZ, 18, 19, 20. Are these keyed to make them error...

I need more info about adding this to a Big Horn. Front-2 sensors in fog light bezels, 2 in bumper grill. My truck doesn't have the end panels on the bumper for the other 2. Are the extra 2 sensors for Advanced Park Assist? Will Park Sense work with 4 sensors? If so, which harness PN do I...

Ok, thanks. I think all connectors have numbers; but I couldn't see any--even with a strong magnifying glass!

This was really helpful. Thanks so much.

My only snag is the ambient connector is wrong on the new driver's door harness I bought. I need a 3 pin connector. Anyone have one? Thanks, Brent

Since the middle map pocket light was eliminated at some point; I modified my 22 BH door panel. Drilled a 1/4" hole for the light to shine through; cut a slot for the "ear" on the light; built a rough post for the screw. I used Fiberflex rod. Seems it stuck well to the door panel gray material.

Well, I discovered that BSG means Belt Starter Generator--which is eTorque. Someway, eTorque requires a second door latch switch on the driver's side. When I was searching for the door harnesses; I looked for Sales Codes for Ambient Lighting and Passive Entry only. Didn't even know BSG was a...

I've run into a small snag. I bought a new door harness; since I wanted to add both Passive Entry and Ambient Lighting. The connector on the new harness for the door lock is a 4 pin connector. Original is an 8. I can swap the wires/pins OK; but the original connector has an additional (5th)...

Good advice. Thanks.

I ordered and received the 6MM. It seems to be correct.

This is a great writeup. And, I really appreciate your research. I'm stuck here. I cannot identify Pin 1 and Pin 2 on this connector. Even using the datasheet; I'm not confident which is which. Also the leads on the new mirror don't correspond to any of the color combinations on the DCCTools...