Search results

I’m not sure what platform that’s from. VinSmart was a lot more specific than the free sites though - it’s a 10 page report. At the time, it was the only one I knew of that had both JD Power & Black Book. Seemingly, for sure - might want to web search whatever yours is vs VinSmart & see what the...

Yes, it took a couple minutes to get into my inbox if I remember right, but that’s it. I got this tip from my brother in law right after he got out of doing car sales at CDJR dealers for 10 years. He still had access to black book values but I needed the printout & this is how I obtained it...

Hopefully this attaches properly. If it doesn’t I’ll attach screenshots. This is what VinSmart looks like. It shows my breakdown when I traded in. You can enter every single detail for your specific car - other sites don’t always have the full package details & some things slip through the...

How do you adjust the tailgate side to side? I’d like to move mine closer to the driver side to get it more even. It’s close enough to the passenger side that it could make contact & affect the paint. If I could move it roughly 1/8”-1/4” to the left it would be where it SHOULD be.

Very nice!

I wonder if that’s just a dealer to dealer thing - the first Ram Laramie I bought before this one, the dealer stacked a ton of rebates & incentives on there. Could be because they were doing employee pricing also, I’m not sure.

It’s important to note also that it doesn’t really have anything to do with the amount of times you’re towing or hauling but what it is and the weight. My truck is usually a street truck that does carry groceries and a hockey bag a few times a week but a couple times a year I will have to load...

Probably better to do it similar to the screenshots above tucked behind the center bezel. I think I’d rather the cord potentially get pinched than too hot or cold because I’m not sure if it would cause some type of short or not. I don’t trust electricity though either. Lol

Just reduces sway in the front I imagine? Night & day as in similar to adding the rear Hellwig sway bar as far as the difference goes?

Consider using VinSmart over the KBB junk. KBB isn’t nearly as accurate & dealers go by Black Book Value anyway. They use KBB to squeeze that extra amount out of you. VinSmart breakdown helped me get more for my trade.

I did this same thing & like it very much also!

Thanks for posting this! Been thinking about doing this on my Limited along with Shift & Grins/Diode Dynamics center light bar,

Man, I wish the Ford dealers around me were like that. They’re the exact opposite. That’s why I’m in a Ram Limited instead of a Raptor. I actually built the Raptor on their website for a grand less than the Limited. There’s more to it though than I care to bore others with on this particular...

Probably going to get a LOT of opinions. I’d say keep it. If I didn’t need a truck I’d get the new Acura Integra. It does have surprisingly a lot of space in the rear, more than the TLX & more comfortable with a hatch & seats that fold down. This past year I test drove a Dodge Charger & Durango...

Check out the thread Shifts & Grins light bar brackets - there’s a post by @ferraiolo1 where he shows what Amazon switch he uses also. Looks very simple & hidden. I didn’t want it at first glance but that’s the route I’m going so that you also don’t have to do anything to do the dash & can reuse...

Also, is it custom or only fit certain trims or ORP, etc?

For sure. The GMC looks a lot better than the Chevy.

Poll question - what to do first: Train horns hooked up to alarm or Ravelco? Train Horns appeal to me more bc it’ll scare them off (likely, but not always) before they get into the cab & you get the revenge factor. Plus you can use them for other safety & cough revenge cough purposes on the...

We camp in the back yard too. If you want to even call it that. 😄

I’m extremely slowly attempting to design an overlay for the front Ram emblem to somewhat match the 2 on the sides to try to blend it all in together. We’ll see how it turns out. Then I’ll have to talk to someone with a 3D printer to figure out how to bring the idea to life. RockKrawler is right...