Search results

You would need 2 of this housing 5-2138650-1 and 4 receptacle tabs 5-963715-1 along with some twisted pair wire for the can bus. I have all this and can make this side. What I still need to identify is the pins for this side of the harness under the drivers seat. Pins 39 to 42 that need...

I purchased the entire LED tail lights with sensors installed on eBay. I will see if I can get some pictures of the wiring.

Correct. The system will work without the mirrors just with sound from the radio. Blind spot will only alert with audio if you turn on your signal when something is in the blind spot. But yes correct. The wiring was not bad but you have to make sure you get the correct polarity on the bus...

I recently went from an 8.4 non nav to a 12" while doing this I also used alfaobd and enabled 360 view. I had to make the wiring for the CVPM 4 wires total 2 CAN bus and 2 power. The coax cable was a pain to run for all the cameras but it can be done. I used generic fakra cables from amazon and...

The glass is not hard to replace but you have to make the wiring. I ended up getting mirrors off eBay with them already. The wiring is in place and just needs plugged in this way.

All settings are in the Body computer and Car configuration change. The last one for the door may or may not be needed? I added the mirrors with the LED so I never tried without it. It will take awhile for the radio to pickup the changes for the menu but it will.

Correct. The heated seat, wheel and camera just pull setting from your truck. If you don't have them they won't show up. Make the changes from post 309 and you will be good to go. Hopefully the next update to the android version will add the option so you can just select Ram 1500 to make the...

I will update this post later today with what I enabled. I also added the mirrors when I installed everything. It will work without the mirrors just with audio.

When I added blind spot sensors and mirrors with blindspot orange LEDs I opted for the ones with the cameras installed. It was a bit running the coax for the left, right, and front cameras but it is doable. I was able to get 360 view working with the swap. All the parts I picked up used and was...

This is available on prime shipping and can be used as SGW bypass to make changes to the BCM. Just unplug the Security gateway under the dash and plug this in. Then you will plug your scanner into it. When finished return the connectors the the SGW...

I am researching the correct pins for the existing connector under the driver seat. If I can find a source I can make the missing wiring that will plug in on the CAN bus side and have 4 pin to add to the current connector under the drivers seat. On my truck that was all I had to add.

You will need to set Cabin NET-ICS Integrated Center Stack set as Not enabled. The Cabin Net-DCSD Display Screen Module should already be set as Enabled. This is why the screen turns on for people with Nav and not with non-nav. When you return it to the old radio just set Cabin NET-ICS...

I would assume you came from an 8.4nav unit then. Could you upload a copy of you BCM status?

I used the following but this is just the major parts. Small hardware is needed for mounting everything. Radio module / brain 68317978AF is what I used. A newer or older part number will be fine. LVDS video cable: 68082364AC was the cheapest one I could find and I used. ( Dodge Journey ) or...

Ebay Ebay, car-part and LKQ. I just watch for deals. I did order the trim from the dealer so it matched my truck.

I updated the post above. Yes volume and every other button works as intended. Took about an hour for the radio to pull the BCM setting for SiriusXM, heated seats etc. A bonus the screen also turn on every time.

Okay so I got everything working from non-nav to 12" ( all knobs and buttons on the screen and the screen starts up every time ) using the Windows version of AlfaOBD. If you had the 8.4 Nav unit to start you may only need to disable Cabin NET-ICS Integrated Center Stack set as Not enabled...

Interesting when I put the truck in reverse the screen comes on and the cameras work but as soon as I take it out of reverse it goes off but the radio still plays.

I made my own wires from some parts I had in my toolbox to finish the missing harness.

The wiring from the tail lights to under the drive seat was present in my truck. 4 CANBus wires were missing from under the seat to the CANBus hub. The connector is a 58 cavity connector XY400A. 39 All Variants D215 DB / WH 0.35 CAN IHS (+) 40 All Variants D216 WH 0.35 CAN IHS (-) 41...