Search results

When I bought my seats, I told the junk yard that I'd buy them only if I could get the wiring harnesses. I didn't know the configuration of the harnesses; but found out that there's a Cabin and an IP harness. I got both harnesses from the donor truck. After I paid them $200 to pull the...

Not directly related to this thread; but the heated/vented passenger seat I had swapped into my truck was "tweeked" from the wreck. No damage to the exterior of the seat; but it leaned about 2" toward the center of the truck. I had tried pry bars and a come-along to straighten it. I helped...

After I installed the new clock spring (Steering Wheel Module) in order to make heated steering wheel work, my left turn signal stopped cancelling. Found out there was a batch of faulty parts, with the AA design level. There's a recall of some 23 and 24 trucks with the bad parts. I won't...

I'm not the OP; but I have some input. Earlier, I swapped heated/vented power passenger seats into my 2022 BH with Level 1 Equipment Group. I had to add a lot of wires to my truck. Once I swapped a center stack with heat/vent switches into my truck, those switches worked without any flashing...

Thanks. Since I posted, I found out there is a recall for "some" 23 and 24 trucks. I don't know if "some" means trucks with heated wheel, of those trucks built before there there was an engineering change to the part. The two PNs are mechanically similar. The difference is that the PN for...

I'm fairly sure the problem is with the part I installed. Since I posted, I did find out there's a recall for this issue. There was a run of bad parts. The recall applies only to 23 and 24 trucks. I'm looking back to see where I bought the part and see if I can exchange for a good one; but...

Have the same problem on my 22 BH. My problem with the dealer will be that I swapped the MFS (with a new part) in my truck to install heated steering wheel. Expect I'll have a problem since the dealer will want to install the PN my VIN calls for--without heated wheel. Maybe I can talk them...

I just did by back seat. It was quite a job. The rear seat I had swapped into my 22 BH was heated and had perforated leather--not vented. The vent bags are adhesive on one side, and they stick to the bottom/back of the seat foams. The blower motors required 3 sheet metal screws to attach. (I...

I'm down to the last step. I bought magnets to attach to the rear wall to hold the flap. Can someone give me a reference on how high to mount the magnets. There's no indentation in my rear wall to show me where to mount the magnets. Thanks, Brent

I'm down to the last step. I've bought magnets to attach to the rear wall to attach the flap. Can someone give me a reference on how high to mount the magnets? There's no indentation on my rear wall to show me what height they should mount. Thanks, Brent

I'm down to the last step. I bought magnets to attach to the rear wall. Can someone give me a reference of how high to mount the magnets? There's no indentation in the rear wall to show me where they should mount. Thanks, Brent

I'm down to the last step. I've found magnets to mount to the rear wall; but can someone give me a reference about how high to mount the magnets. There's no indentation in the rear wall that indicates how high to mount them.

I've bought magnets to install on the rear wall to hold the flap in place. Can someone give me a reference to determine how high the magnets should be mounted? There are no holes in the sheet metal, and no indentations on the rear wall. Thanks, Brent

I took my rear liner out to insulate it; and I can't figure out how to reconnect the center seat belt. Did you find a diagram? Thanks, Brent

The noise from the rear vents seems to be louder than I have had on other vehicles. Really quiets when I turn on recirc, so the flaps are closing. I'm wondering about applying foil/foam insulation to the back of the rear liner, the Panel Inner Silencer. I realize I will need to keep a path...

Can someone tell me, or post a pic of how this flap fastens to the truck?

I got the reclining seat installed. It's nice to show off; but not really much benefit. There's a 'close out' flap behind the center fold down arm rest/console. The flap has 2 snaps; but there's nothing to snap them to on the rear wall of my truck. I've ordered the only part I can find in the...

How do you get the parts? Seems US dealers can't get them. I see there's one side available on eBay for a black market price.

Pretty sure most of the 'facts' about EVs, solar, batteries like $25K to replace the battery, tons of earth moved, child labor, etc. are generated by Big Oil.

Replaced the left side switch and voilà