Search results

kk... next question ... the lights under the drivers and pass floor.. are they the oem led lights or the simple bulb style... the led style actually have two lights in them, one for the interior and the other is the ambient. The ambient lighting only works with the parking/headlights are on...

@D--- does your dimmer look like the one pictured... -=FM45=-

The 'RED' led blinking light should be active when you lock your truck, if not you can turn it on thru the AlpaObd software... -=FM45=-

@Dav -- just thinking, once you get the rear seat parts and wiring figured out... I could be wrong but I believe you will also have to change wiring harness in the console and change/add the rear switches to control the rear heat/vented seats.. You'll also have AlfaObd or the dealer add the...

@ Dav--- just double check that module.. that appears to be 'heat' only... if you need heat/vent, the module looks the same but it has a different part number as well as more plugs being used.... Following :) -=FM45=-

@ all--- this is the part number for the rear seat module--needed.... https://www.moparpartsinc.com/p/Ram_2019_1500-LARAMIE-CREW-CAB-57L-HEMI-V8-4WD/MODULE-Heated-Seat-Rear/75658303/68290175AE.html -=FM45=-

More than likely the wiring isn't there ... with the parts mention above you will also need the module for the rear seats.. module no. 68290175AE Good luck... -=FM45=-

@ Kyles-- try this 68334531AD -=FM45=-

@JK--- do you have heated seats?? The module for heated seats and wheel is under the pass seat... Without that module, there is nothing that will activate it... -=FM45=-

I would swap the wires/pins on the plug- harness side... leave fog harness alone... do both sides ,left and right. What you are doing is just flipping the neg to positive and vice versa.. use pics as reference... -=FM45=-

@Rstan-- if you upgrade oem halogen to oem led, I think you flip the pins in your connectors.... first pic is base--second is prem... -=FM45=-

You can start here--- https://www.moparpartsinc.com/a/Ram_2019_1500-LARAMIE-CREW-CAB-57L-HEMI-V8-4WD/_52016_8238251/Display--Center-Stack/i2544636.html choose the bezel that fits your needs-- ** edit---- I have this in my garage, is this what you're looking for--- -=FM45=-

Colton--- Look at post #28 by Dj... you'll see a white piece of plastic with two holes... that plastic is were the light assembly mounts... -=FM45=-

Does this help ya--- -=FM45=-

@Trav--- I have not had a chance to look thru my toolbox but those pins look correct... the ground is already in both 410/420 plugs, you'll just have to tie into that wire... as far for the 370A, I did not use that for my signal.... connector C6 on the BCM has the wire that I used for the...

@ DJ--- I already have the led assemblies and most wiring for each door... I am adding passive entry at the same time so I only want to open the doors once... Covid has delayed some of my parts. There is one part which is not available from factory, the acrylic tube for bottom map holder.... I...

--- in your pic, if you notice the large yellow plug... the new light assembly will be wired to that... I can give you the pin outs to each side once you get the parts.. You will only need to re-pin two cavities but three will be used... the common ground will be re-used... -=FM45=-

DJ--- If you look under each seat, center rear location, you'll notice a piece of white flat plastic with two holes in it --- one hole is for mounting the other keeps the assembly square.... -=FM45=-

Here is a pic from the rear side of mine, .... (ending in) 1AC ---- I am sure the part you posted just superseeded mine, so essentially they are the same and should work as described.. you do have to make the change in the BCM so that the truck recognizes the new device. Alpha can do everything...

I added 12 volts in the bed area... Pics with a pdf write-up Hope it helps ya-- https://5thgenrams.com/community/threads/what-did-you-do-to-your-ram-today.1686/post-284210 -=FM45=-