Search results

I’ve been wanting to change the color of the bulbs just haven’t got to it yet.

I can technically with software add the alarm feature to any truck. I can do it remotely as well but it would require you sending me the bcm and having a dead vehicle while it’s removed. All of the vehicles have the capability. It’s literally a software switch. How it works for those without...

As I posted in the other 360 request forum. The jl camera setup zauto sells should work for a ram as well you. The only instructions are useless except the part about adding the rca cable to the radio harness. The pin out should be the same. That kit I believe comes with a camera rca adapter...

Actually you can probably use the Jl camera setup zauto sells the installation procedure won’t work as it’s a different car but the pin out for harness should be the same. I can confirm later. Camera should work and it should come with the rca connector to add to the radio. And then use a...

If anyone in Dallas wants to try it to 100 percent confirm I’ve got everything needed to do so. And I’ll be able to activate it without a tazer.

The input is on the single large connector on the back of the radio. You have to add an rca cable with the correct pins. To the harness. You can obtain this rca from z auto. Now no one lists this info. And technically your adding an input for the cargo cam. When 1500s are not equipped with a...

The only time you Will have the surround module is if you have 360. All of the non systems the camera connects directly to the radio harness. However some in site here. For those who just want a front facing camera the radio when not equipped with 360 has a cargo cam input that can be activated...

The only time you Will have the surround module is if you have 360. All of the non systems the camera connects directly to the radio harness. However some in site here. For those who just want a front facing camera the radio when not equipped with 360 has a cargo cam input that can be...

On a 2019 the sgw is located to the left of steering column close to the front of the dash two plugs no tools required for access if your bypassing

The leds on the USB ports are part of the system to keep things charged after shut down. That module will stay active according to the book for 1 hour after shutdown. Plus it’s leds without anything plugged in the draw is probably less than .10 amps. The main cause since it’s been mentioned...

Here is a picture of the two pieces I am referring to. If your problem is similar you can diagnose it by getting down there and barely pressing the brake with your hand or wiggling pedal. As you can see I added a felt tape to prevent these pieces from rubbing. It only happens when you first...

I had this issue as well what I actually did was applied A felt tape to the metal behind the pedal arm. If you look at the pedal assemble the actual brake pedal arm contacts another metal piece before it really brakes. In doing so two pieces of metal rub on one another. Applying grease will...

Is that all on just your truck. I haven’t had any of that on mine. However the window has been tinted to help with direct sun since new

It’s not fare for me to say cost because I work closely with a huge mopar distributor. Plus he had a buyer for the 5.7 before it was out so that got money off of it as well. I will say it’s much cheaper than anything else that gives you the same hp and Tq gains. FYI engine was brand new in...

I’d say if your looking for actual performance gains. You should tune it. Of course that’s the most expensive option however if a super charger is in your future it will be a required step anyway. You can waste your money on add on manipulating devices now but those will be useless later and...

The truck will stay on unless it runs out of gas. However usually it will also make you press the button a few times before it shuts off trying to help you realize no key is present. And if you have pressed on on the key out of vehicle message it usually comes back when trying to shut it off.

The fact that it’s not terminated correctly has me wondering what it’s for. Maybe the sub if you don’t have one or a mistake. However it should be taped up just because you now know it’s there

Here are some pictures. I 100 percent could of been cleaner on the cuts of the plastic. But at the time it was to see if I could do it. And I rushed it. By the way unless you look down it. You can’t tell anything was done from the painted side of the hood.

to modify the stock vents you literally just cut out the lower plastic. the vents are cheap. so if you end up not liking it oh well you can get new ones. I too was worried about water However many cars have vents such as this. I know the fuse box wasn't designed to handle the water however it...

My truck has done this as well As many other things. When it does it again I’m going to try to force only the rfh hub to reset. I can achieve this easily but sitting in the truck with my laptop attached to the obd port.