Search results

I'm down to the last step. I've found magnets to mount to the rear wall; but can someone give me a reference about how high to mount the magnets. There's no indentation in the rear wall that indicates how high to mount them.

I've bought magnets to install on the rear wall to hold the flap in place. Can someone give me a reference to determine how high the magnets should be mounted? There are no holes in the sheet metal, and no indentations on the rear wall. Thanks, Brent

I took my rear liner out to insulate it; and I can't figure out how to reconnect the center seat belt. Did you find a diagram? Thanks, Brent

The noise from the rear vents seems to be louder than I have had on other vehicles. Really quiets when I turn on recirc, so the flaps are closing. I'm wondering about applying foil/foam insulation to the back of the rear liner, the Panel Inner Silencer. I realize I will need to keep a path...

Can someone tell me, or post a pic of how this flap fastens to the truck?

I got the reclining seat installed. It's nice to show off; but not really much benefit. There's a 'close out' flap behind the center fold down arm rest/console. The flap has 2 snaps; but there's nothing to snap them to on the rear wall of my truck. I've ordered the only part I can find in the...

How do you get the parts? Seems US dealers can't get them. I see there's one side available on eBay for a black market price.

Pretty sure most of the 'facts' about EVs, solar, batteries like $25K to replace the battery, tons of earth moved, child labor, etc. are generated by Big Oil.

Replaced the left side switch and voilà

From an earlier post "The 5 choices are 68523482AA, 68523474AA, 68523477AA, 68523479AA, 68523472AA. : Console Wiring" I bought 74. It included the heated/vented switch connectors, two115V connectors, and an extra 12V connector..

See if you can read this one. Also, I have XY430 and 435 connectors, and pins for one of them. I see it truncated some. On XY430A, Pin 1 goes to XY331A Pin 23, then to Assembly-Power Distribution Center C3 Pin 32. Pin 9 goes to XY331A Pin 54, then to Assembly-Power Distribution Center C3 Pin...

Just so pumped that the right switches work! Have ordered another left switch; and hoping both sides will work..

Swapped upgraded rear seat (reclining) into my 2022 BH. Everything works; but I don't have the posts (pins)i n the rear wall to attach the 'close out' carpet piece. I've searched thoroughly in all the rear seat catalog pages and can't find anything. Does anyone have a PN? Thanks.

Thanks. I got around 12V on both the Fused B+ and LIN BUS on both connectors; with respect to each connector's ground--so it seems all 3 pins on both connectors are OK. I even verified the pinning on the Right connector just in case it was made wrong. I couldn't swap the switches because of...

I have a 2022 BH with Level 1 EQ. Last year, I swapped in Heat/Vent Front Seats and Heated Steering Wheel. They didn't require programming to get the hard buttons to work. I have now programmed them with Alfa and the soft buttons now appear on the display. I just swapped in Heat/Vent Rear...

I've made a lot of progress; but have one issue remaining. My truck, 2022 BH with Level 1 EQ, had none of the wires for the rear (also had none for the front) seats. I built a harness with XY430 and XY435A. 6 wires interconnect these 2 connectors. Also had to run 3 Fused Ignitions, 3...

Today's update, and to help my thinking. There is 12V at both the Fused B+ and the LIN BUS pins of the Left seat switch connector. With reference to ground pin in the connector, so apparently the ground is good. I think the LIN BUS is supposed to be around 12V when resting, and sends out a...

Thanks.. I don't totally understand all of them; but doesn't seem like there'd be any value in running this wire to the center console plug (for future mods). The connector, and same description except C2, plug into the Interior Fuse Box..

For sure. I feel somewhat optimistic since the controller is in the left side seat and at least it's communicating with the right side. I'll trace the console harness tomorrow. Can't imagine it doesn't split A207 and LIN BUS to both switches. Incidentally, there's another circuit in...

I see that setting now. Changed it to Programmed; but still have only Left side switches working.