Search results

Mine is slightly below the mid point (30) at idle. I wish it would be at the mid point (just for piece of mind); but I guess it's OK.

My truck already had Auto AC, so I don't know. I would suggest swapping the center stack and seeing if it works. If not, then flash with ALFA. I have this one for sale on eBay. 8" Ram Center Stack Climate Control | Part no. 68340286AC and 68340286AD | eBay

It is an integrated part; clock spring and combi switch. My issue it that I had to replace the part when I installed a heated steering wheel. They don't "give away" the extra 2 connectors with the standard part. The part with the extra 2 terminals (AA engineering change lever) has been found...

I just received a recall notice on a completely separate issue, ABS Module Configuration Mismatch. I took my truck to the dealership. Was told the software is not available yet. While I was there, I brought up the turn signal issue. I was totally open; I bought the Multi Function switch...

Original Multi-Function Switch part 68545657AA was around $300. Engineering change level AB , which supersedes AA, is around $70. I guess I should just buy AB; but it sounds too good to be true. Any information? Thanks, Brent

To clarity, there are no additional wires required to add the center stack with physical buttons. The center stack is CANBUS (or whatever it's called now) connected, so it's plug and play. The 3 wires I talked about send Fused Ignition to XY420A (big yellow seat connector). I THINK these 3...

I see the link doesn't work. It's for the FB Marketplace 5th Gen Rams Buy/Sell/Trade. I also have it listed on eBay. It's the Center Stack with the heated seat switches. 8" Ram Center Stack Climate Control | Part no. 68340286AC and 68340286AD | eBay

I'm searching for a better diagram; but I'm fairly sure I had run 2 (maybe all 3) of the PK/YE Fused Ignition (Pins 1,3,5 of XY420A (PASS on the screenshot) across the IP to ASSEMBLY-POWER DISTRIBUTION CENTER-INTERIOR C3 (Pins 17, 6, 27 and circuits F921, F924, FF922 , respectively) . These 3...

I have this part for sale, if you need it. Log into Facebook

When I bought my seats, I told the junk yard that I'd buy them only if I could get the wiring harnesses. I didn't know the configuration of the harnesses; but found out that there's a Cabin and an IP harness. I got both harnesses from the donor truck. After I paid them $200 to pull the...

Not directly related to this thread; but the heated/vented passenger seat I had swapped into my truck was "tweeked" from the wreck. No damage to the exterior of the seat; but it leaned about 2" toward the center of the truck. I had tried pry bars and a come-along to straighten it. I helped...

After I installed the new clock spring (Steering Wheel Module) in order to make heated steering wheel work, my left turn signal stopped cancelling. Found out there was a batch of faulty parts, with the AA design level. There's a recall of some 23 and 24 trucks with the bad parts. I won't...

I'm not the OP; but I have some input. Earlier, I swapped heated/vented power passenger seats into my 2022 BH with Level 1 Equipment Group. I had to add a lot of wires to my truck. Once I swapped a center stack with heat/vent switches into my truck, those switches worked without any flashing...

Thanks. Since I posted, I found out there is a recall for "some" 23 and 24 trucks. I don't know if "some" means trucks with heated wheel, of those trucks built before there there was an engineering change to the part. The two PNs are mechanically similar. The difference is that the PN for...

I'm fairly sure the problem is with the part I installed. Since I posted, I did find out there's a recall for this issue. There was a run of bad parts. The recall applies only to 23 and 24 trucks. I'm looking back to see where I bought the part and see if I can exchange for a good one; but...

Have the same problem on my 22 BH. My problem with the dealer will be that I swapped the MFS (with a new part) in my truck to install heated steering wheel. Expect I'll have a problem since the dealer will want to install the PN my VIN calls for--without heated wheel. Maybe I can talk them...

I just did by back seat. It was quite a job. The rear seat I had swapped into my 22 BH was heated and had perforated leather--not vented. The vent bags are adhesive on one side, and they stick to the bottom/back of the seat foams. The blower motors required 3 sheet metal screws to attach. (I...

I'm down to the last step. I bought magnets to attach to the rear wall to hold the flap. Can someone give me a reference on how high to mount the magnets. There's no indentation in my rear wall to show me where to mount the magnets. Thanks, Brent

I'm down to the last step. I've bought magnets to attach to the rear wall to attach the flap. Can someone give me a reference on how high to mount the magnets? There's no indentation on my rear wall to show me what height they should mount. Thanks, Brent

I'm down to the last step. I bought magnets to attach to the rear wall. Can someone give me a reference of how high to mount the magnets? There's no indentation in the rear wall to show me where they should mount. Thanks, Brent